Effects of Stacking Sequence on Mode II Delamination in Hybrid Carbon/Flax Reinforced Epoxy Composites
W.K. SEE, M. JOHAR, K.J. WONG, W.W.F. CHONG, A.B. CHAI
Abstract. With increasing environmental awareness, natural fibres such as flax are gaining attention in polymer composite applications due to their sustainability. This study investigates the Mode II delamination behaviour of hybrid carbon/flax epoxy composites with three stacking configurations: carbon–carbon (C//C), flax–flax (F//F), and carbon–flax (C//F). Specimens were fabricated using a hand lay-up technique followed by vacuum-bagging and tested using the End Notched Flexure (ENF) method. The measured Mode II fracture toughness values (GIIC) were 1416.10 ± 64.52 N/m for C//C, 1396.06 ± 95.42 N/m for F//F, and 2892.69 ± 216.35 N/m for C//F. The C//F configuration exhibited significantly higher toughness — approximately double that of the other two — suggesting enhanced resistance to delamination due to increased interfacial friction between dissimilar fibre types. These findings demonstrate that hybridisation, particularly with carbon/flax interfaces, can effectively improve the interlaminar fracture toughness of composite laminates. The results provide valuable insights for the design of sustainable, high-performance composite structures, especially in applications where delamination resistance is critical.
Keywords
Hybrid Composites, Carbon/Flax Epoxy, Stacking Sequence, Mode II Fracture, Delamination
Published online 11/15/2026, 8 pages
Copyright © 2026 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: W.K. SEE, M. JOHAR, K.J. WONG, W.W.F. CHONG, A.B. CHAI, Effects of Stacking Sequence on Mode II Delamination in Hybrid Carbon/Flax Reinforced Epoxy Composites, Materials Research Proceedings, Vol. 74, pp 125-132, 2026
DOI: https://doi.org/10.21741/9781644904473-16
The article was published as article 16 of the book Composite Science and Technology
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] L. Pil, F. Bensadoun, J. Pariset, I. Verpoest, Why are designers fascinated by flax and hemp fibre composites?, Compos. Part A-Appl. S. (2016) 83 193-205. https://doi.org/10.1016/j.compositesa.2015.11.004.
[2] M. Chandrasekar, M.R. Ishak, S.M. Sapuan, Z. Leman, M. Jawaid, A review on the characterisation of natural fibres and their composites after alkali treatment and water absorption, Plast. Rubber Compos. (2017) 46(3) 119-136. https://doi.org/10.1080/14658011.2017.1298550.
[3] K.L. Pickering, M.G.A. Efendy, T.M. Le, A review of recent developments in natural fibre composites and their mechanical performance, Compos. Part A-Appl. S. (2016) 83 98-112. https://doi.org/10.1016/j.compositesa.2015.08.038.
[4] L. Yan, N. Chouw, K. Jayaraman, Flax fibre and its composites – A review, Compos. Part B-Eng. (2014) 56 296-317. https://doi.org/10.1016/j.compositesb.2013.08.014.
[5] A. Turon, P.P. Camanho, J. Costa, C.G. Dávila, A damage model for the simulation of delamination in advanced composites under variable-mode loading, Mechanics of Materials (2006) 38(11) 1072-1089. http://dx.doi.org/10.1016/j.mechmat.2005.10.003.
[6] Y. Zhao, W. Liu, L.K. Seah, G.B. Chai, Delamination growth behavior of a woven E-glass/bismaleimide composite in seawater environment, Compos. Part B-Eng. (2016) 106 332-343. http://dx.doi.org/10.1016/j.compositesb.2016.09.045.
[7] N.J. Pagano, G.A. Schoeppner, Delamination of polymer matrix composites: problems and assessment, in: A. Kelly and C. Zweben, (Eds.), Comprehensive Composite Materials, Pergamon, Oxford, 2000. pp. 433-528. http://doi.org/10.1016/B0-08-042993-9/00073-5.
[8] M. Ravandi, W.S. Teo, M.S. Yong, T.E. Tay, Prediction of Mode I interlaminar fracture toughness of stitched flax fiber composites, J. Mater. Sci. (2018) 53(6) 4173-4188. https://doi.org/10.1007/s10853-017-1859-y.
[9] M. Ravandi, W.S. Teo, L.Q.N. Tran, M.S. Yong, T.E. Tay, The effects of through-the-thickness stitching on the Mode I interlaminar fracture toughness of flax/epoxy composite laminates, Mater. Des. (2016) 109 659-669. https://doi.org/10.1016/j.matdes.2016.07.093.
[10] F. Bensadoun, I. Verpoest, A.W. Van Vuure, Interlaminar fracture toughness of flax-epoxy composites, Journal of Reinforced Plastics and Composites (2017) 36(2) 121-136. https://doi.org/10.1177/0731684416672925.
[11] C. Chen, Y. Li, T. Yu, Interlaminar toughening in flax fiber-reinforced composites interleaved with carbon nanotube buckypaper, Journal of Reinforced Plastics and Composites (2014) 33(20) 1859-1868. https://doi.org/10.1177/0731684414548084.
[12] F.A. Almansour, H.N. Dhakal, Z.Y. Zhang, Investigation into Mode II interlaminar fracture toughness characteristics of flax/basalt reinforced vinyl ester hybrid composites, Composites Science and Technology (2018) 154 117-127. https://doi.org/10.1016/j.compscitech.2017.11.016.
[13] T.S. Rajendran, M. Johar, K.O. Low, S. Abu Hassan, K.J. Wong, Interlaminar fracture toughness of a plain weave flax/epoxy composite, Plast. Rubber Compos. (2019) 48(2) 74-81. https://doi.org/10.1080/14658011.2018.1550235.
[14] S. Benmedakhene, M. Kenane, M.L. Benzeggagh, Initiation and growth of delamination in glass/epoxy composites subjected to static and dynamic loading by acoustic emission monitoring, Compos. Sci. Technol. (1999) 59(2) 201-208. https://doi.org/10.1016/S0266-3538(98)00063-3.
[15] J. Summerscales, N.P.J. Dissanayake, A.S. Virk, W. Hall, A review of bast fibres and their composites. Part 1 – Fibres as reinforcements, Compos. Part A-Appl. S. (2010) 41(10) 1329-1335. https://doi.org/10.1016/j.compositesa.2010.06.001.
[16] M. Johar, W.W.F. Chong, K.J. Wong, Moisture absorption and tensile behaviour of hybrid carbon/flax composites, Fibers Polym. (2023) 24(5) 1799-1810. https://doi.org/10.1007/s12221-023-00157-0.
[17] G.R. Irwin, J.A. Kies, Critical energy rate analysis of fracture strength, Weld. J. Res. Suppl. (1954) 33 193-198.
[18] K. Tanaka, K. Kageyama, M. Hojo, Prestandardization study on mode II interlaminar fracture toughness test for cfrp in japan, Compos. (1995) 26(4) 257-267. https://doi.org/10.1016/0010-4361(95)93669-B.
[19] P.N.B. Reis, J.A.M. Ferreira, J.D.M. Costa, A.M. Pereira, Interlaminar fracture in woven carbon/epoxy laminates, Frat. Integrita Strutt. (2014) 30 431-437.
[20] W. Trabelsi, L. Michel, R. Othomene, Effects of stitching on delamination of satin weave carbon-epoxy laminates under mode I, mode II and mixed-mode I/II loadings, Applied Composite Materials (2010) 17(6) 575-595. https://doi.org/10.1007/s10443-010-9128-0.
[21] Y. Zhao, M. Cao, W.P. Lum, V.B.C. Tan, T.E. Tay, Interlaminar fracture toughness of hybrid woven carbon-Dyneema composites, Compos. Part A-Appl. S. (2018) 114 377-387. https://doi.org/10.1016/j.compositesa.2018.08.035.
[22] Y. Saadati, J.-F. Chatelain, G. Lebrun, Y. Beauchamp, P. Bocher, N. Vanderesse, A study of the interlaminar fracture toughness of unidirectional flax/epoxy composites, J. Compos. Sci. (2020) 4(2). https://doi.org/10.3390/jcs4020066.
[23] V. Prasad, K. Sekar, S. Varghese, M.A. Joseph, Enhancing Mode I and Mode II interlaminar fracture toughness of flax fibre reinforced epoxy composites with nano TiO2, Compos. Part A-Appl. S. (2019) 124 105505. https://doi.org/10.1016/j.compositesa.2019.105505.
[24] F.A. Almansour, H.N. Dhakal, Z.Y. Zhang, H. Ghasemnejad, Effect of hybridization on the mode II fracture toughness properties of flax/vinyl ester composites, Polym. Compos. (2017) 38(8) 1732-1740. https://doi.org/10.1002/pc.23743.

