Influence of Drying Heat Treatment on Physical and Mechanical Properties of Mycelium Based Composite
Zatty MINAI, M.K.R HASHIM, Noorulnajwa Diyana YAACOB, M.N.A.UDA, Z.A. ARSAT, M. Firdaus A. MUTTALIB, F. ABDULLAH, S.M. SHAHRIL, Nur Khuzaima AZMAN, M.A.M. AKHIR
Abstract. Mycelium-based composites (MBCs) were studied in context of high carbon materials as a sustainable solution and dried at 70°C, 75°C and 80°C and examined their physical, mechanical and morphological properties. One-way ANOVA confirmed that drying temperature was a statistically significant parameter, or critical factor, in the performance. Dried at 75°C, the specimens were found to have the highest density (0.3508 g/cm³), shrinkage of 24.9% and ductile failure under compression, which represented optimal structural integrity for lightweight, non-load-bearing use. The samples obtained at 70°C showed the maximum compressive strength with brittle failure and density of 0.3486g/cm³ with shrinkage of 20.22%. Morphological analysis by the SEM showed good hyphal bonding in both 70°C and 75°C groups. On the other hand, the 80°C samples showed bad bonding, lowest compressive strength, 27.8% shrinkage and porous internal structure because of over-drying. The drying condition of 75°C is the best one for sustainable building materials.
Keywords
Mycelium-Based Composites, Drying Temperature, Physical Properties, Compressive Strength, Morphological Analysis
Published online 11/15/2026, 8 pages
Copyright © 2026 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Zatty MINAI, M.K.R HASHIM, Noorulnajwa Diyana YAACOB, M.N.A.UDA, Z.A. ARSAT, M. Firdaus A. MUTTALIB, F. ABDULLAH, S.M. SHAHRIL, Nur Khuzaima AZMAN, M.A.M. AKHIR, Influence of Drying Heat Treatment on Physical and Mechanical Properties of Mycelium Based Composite, Materials Research Proceedings, Vol. 74, pp 117-124, 2026
DOI: https://doi.org/10.21741/9781644904473-15
The article was published as article 15 of the book Composite Science and Technology
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] A. Senanu, K. Kukah, A. Victor, K. Blay, A. Opoku, International Journal of Real Estate Studies INTREST Strategies to Reduce the Impact of Resource Consumption in the Ghanaian Construction Industry (2022)
[2] Z.H. Wang, A Survey of Factors and Life Cycle Assessment in Selection of Green Construction Materials, Journal of Computational Intelligence in Materials Science 1 (2023) 23–33. https://doi.org/10.53759/832X/JCIMS202301003
[3] S. Damseth, K. Thakur, R. Kumar, S. Kumar, D. Mahajan, H. Kumari, D. Sharma, A.K. Sharma, Assessing the impacts of river bed mining on aquatic ecosystems: A critical review of effects on water quality and biodiversity, HydroResearch 7 (2024) 122–130. https://doi.org/10.1016/j.hydres.2024.01.004
[4] M.K.R. Hashim, M.S. Abdul Majid, M.R. Mohd Jamir, F.H. Kasim, H.A. Alshahrani, M.A.M. Deros, D. Hui, Effects of Ply Orientations and Stacking Sequences on Impact Response of Pineapple Leaf Fibre (PALF)/Carbon Hybrid Laminate Composites, Materials (Basel) 15 (2022) 6121. https://doi.org/10.3390/ma15176121
[5] K.K. Alaneme, J.U. Anaele, T.M. Oke, S.A. Kareem, M. Adediran, O.A. Ajibuwa, Y.O. Anabaranze, Mycelium based composites: A review of their bio-fabrication procedures, material properties and potential for green building and construction applications, Alexandria Engineering Journal 83 (2023) 234–250. https://doi.org/10.1016/j.aej.2023.10.012
[6] M.S. Soffian, F.Z. Abdul Halim, F. Aziz, M.A.Rahman, M.A. Mohamed Amin, D.N. Awang Chee, Carbon-based material derived from biomass waste for wastewater treatment, Environ. Adv., 9 (2022) 100259. https://doi.org/10.1016/j.envadv.2022.100259
[7] R. Volk, M. Schröter, N. Saeidi, S. Steffl, A. Javadian, D.E. Hebel, F. Schultmann, Life cycle assessment of mycelium-based composite materials, Resour. Conserv. Recycl. 205 (2024) 107579. https://doi.org/10.1016/j.resconrec.2024.107579
[8] C. Kohphaisansombat, Y. Jongpipitaporn, P. Laoratanakul, S. Tantipaibulvut, J. Euanorasetr, N. Rungjindamai, C. Chuaseeharonnachai, P. Kwantong, S. Somrithipol, N. Boonyuen, Fabrication of mycelium (oyster mushroom)-based composites derived from spent coffee grounds with pineapple fibre reinforcement, Mycology 15 (2024) 665–682. https://doi.org/10.1080/21501203.2023.2273355
[9] M.E. Voutetaki and A.C. Mpalaskas, Natural Fiber-Reinforced Mycelium Composite for Innovative and Sustainable Construction Materials, Fibers 12 (2024) 57. https://doi.org/10.3390/fib12070057
[10] S. Sozcu, J. Frajova, J. Wiener, M. Venkataraman, B. Tomkova, J. Militky, Effect of Drying Methods on the Thermal and Mechanical Behavior of Bacterial Cellulose Aerogel., Gels (Basel, Switzerland) 10 (2024) 474. https://doi.org/10.3390/gels10070474
[11] A. Farrahnoor, A.D.N. Hishamuddini, H. Yusoff, M.H. Koay, N.C. Maideen, N.A.M. Fohimi, T.Z. Boey, Influence of Drying Temperature in the Oven on Physical, Morphology and Mechanical Properties of Mycelium Composite, Pertanika Journal of Science and Technology 33 (2025) 219. https://doi.org/10.47836/pjst.33.1.10
[12] W. Aiduang, J. Kumla, S. Srinuanpan, W. Thamjaree, S. Lumyong, N. Suwannarach, Mechanical, Physical, and Chemical Properties of Mycelium-Based Composites Produced from Various Lignocellulosic Residues and Fungal Species, J. fungi (Basel, Switzerland), 8 (2022) 1125. https://doi.org/10.3390/jof8111125
[13] Standard Test Method for iTeh Standards iTeh Standards, ASTM Int., vol. 1, no. October, 2022, pp. 22–25. https://doi.org/10.1520/D2395-17R22.2
[14] E. Elsacker, S. Vandelook, J. Brancart, E. Peeters, L. De Laet, Mechanical, physical and chemical characterisation of mycelium-based composites with different types of lignocellulosic substrates, PLoS One 14 (2019) 1–20. https://doi.org/10.1371/journal.pone.0213954
[15] I.S. Santos, B.L. Nascimento, R.H. Marino, E.M. Sussuchi, M.P. Matos, S. Griza, Influence of drying heat treatments on the mechanical behavior and physico-chemical properties of mycelial biocomposite, Compos. Part B Eng. 217 (2021) 108870. https://doi.org/10.1016/j.compositesb.2021.108870
[16] L. Yang, D. Park, Z. Qin, Material Function of Mycelium-Based Bio-Composite: A Review, Front. Mater. 8 (2021) 737377. https://doi.org/10.3389/fmats.2021.737377.

