Design to Manufacturing Process Calibration and Simulation of LPBF Structures
Ijaz AKBAR, Djamel ABOU MAAMAR, Mohamed El IBRAHIMI, Kevin Nocentini
Abstract. In LPBF, printing failures are mainly driven due to thin-wall structures, use of non-calibrated machines and material parameters. Hereof, to pre-identify the design for additive thin walls (DFATW), a macro-design tool is under development that could predict the existence of thin walls below a threshold so the critical zones could be treated to be printable with LPBF process. In addition, an AI4AM approach is developed to predict the combined and individual influence driven by process parameters, especially around melt-pool dimensions, length, width, and height. These dimensions predicted by AI4AM are cross validated following an MAPE of < 6% with FEM so from hundreds of process parameters the best combination could be identified in seconds to better train the LPBF machine. Finally, the process simulation modelling based on AI4AM predictions is performed to investigate further process driven defects. The LPBF simulation results showed that the as produced and heat-treated structures have significant differences in structural distortion and final residual stresses (an approximately 35% reduction).
Keywords
Design of Thin Walls; Machine Learning; Process Parameters; LPBF Process Simulation
Published online 11/8/2026, 6 pages
Copyright © 2026 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Ijaz AKBAR, Djamel ABOU MAAMAR, Mohamed El IBRAHIMI, Kevin Nocentini, Design to Manufacturing Process Calibration and Simulation of LPBF Structures, Materials Research Proceedings, Vol. 73, pp 72-77, 2026
DOI: https://doi.org/10.21741/9781644904459-15
The article was published as article 15 of the book Mechanics of Advanced Materials and Structures
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] G. Weil, G., Analytical and numerical analyses of neo-Hookean thin-wall composite spheres, Mathematics and Mechanics of Solids 24 (2019) 1800–1820. https://doi.org/10.1177/1081286518807257
[2] Z. Wang, C. Jiang, P. Liu, W. Yang, Y. Zhao, M.F. Horstemeyer, L.Q. Chen, Z. Hu, L. Chen, Uncertainty quantification and reduction in metal additive manufacturing, NPJ Comput. Mater. 6 (2020). https://doi.org/10.1038/s41524-020-00444-x
[3] Z. Wu, S.P. Narra, A. Rollett, Exploring the fabrication limits of thin-wall structures in a laser powder bed fusion process, (2020). https://doi.org/10.1007/s00170-020-05827-4/
[4] G. Vastola, W.J. Sin, C.N. Sun, N. Sridhar, Design guidelines for suppressing distortion and buckling in metallic thin-wall structures built by powder-bed fusion additive manufacturing, Mater. Des. 215 (2022). https://doi.org/10.1016/j.matdes.2022.110489
[5] D. Wang, H. Fang, R. Xue, S. Li, Numerical study on the axial collapse of thin-walled columns, Sci. Rep. 14 (2024). https://doi.org/10.1038/s41598-024-56558-5
[6] J. Zhou, R.A. Barrett, S.B. Leen, Three-dimensional finite element modelling for additive manufacturing of Ti-6Al-4V components: Effect of scanning strategies on temperature history and residual stress, Journal of Advanced Joining Processes 5 (2022). https://doi.org/10.1016/j.jajp.2022.100106
[7] M.T. Khan, W. Feng, L. Chen, Y.H. Ng, N. Yew, J. Tan, S.K. Moon, DETC2024-XXXXX Automatic Feature Recognition and Dimensional Attributes Extraction from CAD Models for Hybrid Additive-Subtractive Manufacturing, n.d.
[8] Z. Wu, S.P. Narra, A. Rollett, Exploring the fabrication limits of thin-wall structures in a laser powder bed fusion process, (n.d.). https://doi.org/10.1007/s00170-020-05827-4/
[9] W. Shen, X. Zhang, X. Jiang, L.H. Yeh, Z. Zhang, Q. Li, B. Li, H. Qin, Surface extraction from micro-computed tomography data for additive manufacturing, in: Procedia Manuf., Elsevier B.V., 2021: pp. 568–575. https://doi.org/10.1016/j.promfg.2021.06.057
[10] M. Inui, N. Umezu, K. Wakasaki, S. Sato, Thickness and clearance visualization based on distance field of 3D objects, J. Comput. Des. Eng. 2 (2015) 183–194. https://doi.org/10.1016/j.jcde.2015.04.001
[11] P. Tan, F. Shen, B. Li, K. Zhou, A thermo-metallurgical-mechanical model for selective laser melting of Ti6Al4V, Mater. Des. 168 (2019). https://doi.org/10.1016/j.matdes.2019.107642
[12] J.R. Zhuang, Y.T. Lee, W.H. Hsieh, A.S. Yang, Determination of melt pool dimensions using DOE-FEM and RSM with process window during SLM of Ti6Al4V powder, Opt. Laser Technol. 103 (2018) 59–76. https://doi.org/10.1016/j.optlastec.2018.01.013
[13] H.L.W. a, J.S.Z. a, T.M. a, J.W.E. b, J.O.M. c, A.M.B. a, A.W.-H. a, A.D. d, W.Z. e T. DebRoy a, Additive manufacturing of metallic components – Process, structure and properties, Prog. Mater. Sci. (2018).
[14] N. Ahmed, I. Barsoum, R.K. Abu Al-Rub, Numerical investigation of residual stresses in thin-walled additively manufactured structures from selective laser melting, Heliyon 9 (2023). https://doi.org/10.1016/j.heliyon.2023.e19385
[15] S. Önder, N. Saklakoğlu, A. Sever, Selective laser melting of Ti6Al4V alloy: Effect of post-processing on fatigue life, residual stress, microstructure, microhardness and surface roughness, Mater. Charact. 196 (2023). https://doi.org/10.1016/j.matchar.2022.112571

