Effect of Air Abrasion Surface Treatment on the Bonding Behavior at Zirconia-Resin Interface

Effect of Air Abrasion Surface Treatment on the Bonding Behavior at Zirconia-Resin Interface

N.S. AMINUDDIN, M.F.A. RAHIM, N.H. JAMADON

Abstract. Zirconia 3YSZ is a superior material for dental restoration because it has the best mechanical strength, aesthetics and biocompatibility. Creating a reliable and durable bond to the surface of zirconia is difficult due to its inert chemical nature and has limited its use. However, the introduction of functional monomers such as methacryloyloxydecyl dihydrogen phosphate (MDP) in cementation materials has increased the bond strength to zirconia. The main objective of this study is to investigate the effects of surface treatment on the bond strength of novel zirconia and commercially available adhesive cements. The prepared zirconia samples were divided into two groups: without surface treatment and with surface treatment (air-particle abrasion, 50 μm). Surface roughness was tested with an electronic profilometer (Ra). Adhesive cement (RelyX Ultimate Clicker, 3M) is applied to the zirconia surface. The microstructure of the zirconia is also characterised. After surface treatment, the zirconia exhibited higher surface roughness (Ra = 17.19 ± 4.13) than without surface treatment (Ra = 3.72 ± 0.51). The zirconia phase is mostly in a tetragonal phase with a few monoclinic phases. The change in surface roughness further promotes cell attachment. Sintering samples at 1500 °C gave good microstructural density and does not cause the grains to pull out; this is the most suitable temperature for producing zirconia with good mechanical properties. The bonding effect of the cement is related to its ability to penetrate the surface irregularities of the substrate, the mechanical properties being influenced by the total filler content. The presence of 43 wt% total filler can improve mechanical properties and reduce solubility.

Keywords
Air Abrasion, Bonding Behaviour, Zirconia-Resin

Published online 7/15/2026, 7 pages
Copyright © 2026 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: N.S. AMINUDDIN, M.F.A. RAHIM, N.H. JAMADON, Effect of Air Abrasion Surface Treatment on the Bonding Behavior at Zirconia-Resin Interface, Materials Research Proceedings, Vol. 68, pp 232-238, 2026

DOI: https://doi.org/10.21741/9781644904237-31

The article was published as article 31 of the book Green Materials, Processing & Characterization

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

References
[1] S. C. Bayne, J. L. Ferracane, G. W. Marshall, S. J. Marshall, and R. van Noort, J. Dent. Res. 98(3), 257-265 (2019). https://doi.org/10.1177/0022034518822808
[2] L. Zhao, Y. T. Jian, X. D. Wang, and K. Zhao, J. Prosthet. Dent. 116(5), 790-796 (2016). https://doi.org/10.1016/j.prosdent.2016.03.020
[3] I. Denry and J. R. Kelly, Dent. Mater. 24(3), 299-307 (2008). https://doi.org/10.1016/j.dental.2007.05.007
[4] N. F. Amat, A. Muchtar, N. Yahaya, and M. J. Ghazali, Aust. J. Basic Appl. Sci. 6(12), 9-13 (2012).
[5] A. Ghasemi et al., J. Adhes. Dent. 16(4), 377-382 (2014).
[6] R. M. Dawood and A. F. Ibraheem, J. Baghdad Coll. Dent. 27(1), 77-85 (2015). https://doi.org/10.12816/0015268
[7] S. C. Lin, W. C. Lin, T. C. Hu, M. Yan, and C. M. Tang, Coatings 11(9), (2021). https://doi.org/10.3390/coatings11091017
[8] R. M. Melo, R. O. A. Souza, E. Dursun, E. B. C. Monteiro, L. F. Valandro, and M. A. Bottino, Oper. Dent. 40(6), 636-643 (2015). https://doi.org/10.2341/14-144-L
[9] D. M. D. Moura et al., J. Mech. Behav. Biomed. Mater. 88, 69-77 (2018).
[10] N. Faeizah Amat Andanastuti Muchtar, M. Jameelah Ghazali, and N. Yahaya, J. Mech. Eng. 4(3), 10-19 (2017).
[11] M. Seipenbusch, S. Rothenbacher, M. Kirchhoff, H. J. Schmid, G. Kasper, and A. P. Weber, J. Nanoparticle Res. 12(6), 2037-2044 (2010). https://doi.org/10.1007/s11051-009-9760-5
[12] N. F. Amat, A. Muchtar, M. S. Amril, M. J. Ghazali, and N. Yahaya, Ceram. Int. 44(6), 6409-6416 (2018). https://doi.org/10.1016/j.ceramint.2018.01.035
[13] R. Gamal, Y. F. Gomaa, and M. A. Abdellatif, Futur. Dent. J. 3(2), 55-60 (2017). https://doi.org/10.1016/j.fdj.2017.07.002
[14] S. H. Youm, K. H. Jung, S. A. Son, Y. H. Kwon, and J. K. Park, J. Adv. Prosthodont. 7(4), 317-322 (2015). https://doi.org/10.4047/jap.2015.7.4.317