Phase, Structure and Compressive Strength of Sintered Perlis Dolomite/Silica
Nur Hasnidah AHMAD SHUKERI, Syed Nuzul Fadzli SYED ADAM, Firuz ZAINUDDIN, Hasmaliza MOHAMAD, Heah CHENG YONG
Abstract. Natural dolomite sedimentary rocks, which can be found in abundance in Perlis, is a carbonate mineral rich with calcium and magnesium elements. These both elements were important and typically found in bioceramic materials especially for hard tissue implant material. Even though raw Perlis dolomite powder has other various elemental compositions, it lacks important components such as silica which commonly acts as glass network former, in resulting limits its potential application as bioceramic materials. This study investigates the effects of different compositions of silica addition on sintered Perlis dolomite and the changes in their phase transformation, structure and compressive strength were analyzed. Perlis dolomite with different ratios of silica (30S, 35S and 40S) were ball milled, compacted into pallets and sintered at 1300°C for 4 hours. The results show that the silica contents gave a significant impact on the phase transformation of the resulting materials involving akermanite, monticellite and merwinite. At lower silica content (30S), monticellite and merwinite became dominant phases with a slight amount of akermanite. But increasing silica content leads to the formation of akermanite phase, while reducing the monticellite and merwinite phase and merwinite phase completely disappeared at 40S. This result expressed that the higher silica encourages the stabilization of akermanite at the expense of other calcium–magnesium silicate phases supported with improvement in compressive strength (14-18 MPa), which is promising for bone tissue regenerations.
Keywords
Perlis Dolomite, Silica, Akermanite, Monticellite, Merwinite
Published online 7/15/2026, 9 pages
Copyright © 2026 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Nur Hasnidah AHMAD SHUKERI, Syed Nuzul Fadzli SYED ADAM, Firuz ZAINUDDIN, Hasmaliza MOHAMAD, Heah CHENG YONG, Phase, Structure and Compressive Strength of Sintered Perlis Dolomite/Silica, Materials Research Proceedings, Vol. 68, pp 17-25, 2026
DOI: https://doi.org/10.21741/9781644904237-3
The article was published as article 3 of the book Green Materials, Processing & Characterization
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] D. H. M. Rao., K. Rajkumar, D. V. Narayana, Akash M, D. J. Sabu, and D. R. Ramadoss, “Bioinert And Bioactive Materials ––Narrative Review,” Journal of Pharmaceutical Negative Results, vol. 13, no. 7, pp. 2251–2255, 2022. https://doi.org/10.47750/pnr.2022.13.S07.309
[2] J. Yu, J. Qian, F. Wang, J. Qin, X. Dai, C. You, and X. Jia, “Study of using dolomite ores as raw materials to produce magnesium phosphate cement,” Constr. Build. Mater., vol. 253, 2020. https://doi.org/10.1016/j.conbuildmat.2020.119147
[3] R. A. Youness, D. M. Tag, and M. A. Taha, “A Review on Calcium Silicate Ceramics : Properties , Limitations , and Solutions for Their Use in Biomedical Applications,” Silicon, vol. 15(6), pp. 2493–2505, 2023.
[4] M. Ahmadipour, H. Mohammadi, A. L. Pang, M. Arjmand, T. Ayode Otitoju, P. U. Okoye, and B. Rajitha, “A review: silicate ceramic-polymer composite scaffold for bone tissue engineering,” International Journal of Polymeric Materials and Polymeric Biomaterials, vol. 71, no. 3. 2022. https://doi.org/10.1080/00914037.2020.1817018
[5] H. Mohammadi, Y. M. Baba Ismail, K. A. Bin Shariff, and A. F. Mohd Noor, “Synthesis and Characterization of Akermanite by Mechanical Milling and Subsequent Heat Treatment,” in Journal of Physics: Conference Series, 2018, vol. 1082, no. 1. https://doi.org/10.1088/1742-6596/1082/1/012021
[6] Y. Arkame, A. Harrati, M. Jannaoui, Y. Et-Tayea, I. Yamari, A. Sdiri, and C. Sadik, “Effects of slag addition and sintering temperature on the technological properties of dolomite based porous ceramics,” Open Ceram., vol. 13, 2023. https://doi.org/10.1016/j.oceram.2023.100333
[7] A. Harrati, Y. Arkame, A. Manni, S. Aqdim, R. Zmemla, A. Chari, A. El Bouari, I.E.E.A. El Hassani, A. Sdiri, F.O. Hassani, and C. Sadik, “Akermanite-based ceramics from Moroccan dolomite and perlite: Characterization and in vitro bioactivity assessment,” Open Ceram., vol. 10, p. 100276, Jun. 2022. https://doi.org/10.1016/j.oceram.2022.100276
[8] C. Azurahanim, E. L. Albert, L. Gee Een, M. A. Zarin, and M. Z. Mohd Yusoff, “Effect of Thermal Treatment on Physical Properties of Malaysian Dolomitic Limestone,” Int. J. Electroact. Mater, 2022.
[9] F. F. Kamarzaman, M. M. A. B. Abdullah, S. Z. Abd Rahim, A. A. Kadir, N. H. Jamil, W. M. W. Ibrahim, and A. V. Sandu, “Hydroxyapatite / Dolomite alkaline activated material reaction in the formation of low temperature sintered ceramic as adsorbent materials,” vol. 349, no. August, 2022.
[10] P. H. Huang, M. Laakso, P. Edinger, O. Hartwig, G.S. Duesberg, L.L. Lai, J. Mayer, J. Nyman, C. Errando-Herranz, G. Stemme, and K.B. Gylfason, “Three-dimensional printing of silica glass with sub-micrometer resolution,” Nat. Commun., vol. 14, no. 1, 2023. https://doi.org/10.1038/s41467-023-38996-3.
[11] K. H. Min, D. H. Kim, K. H. Kim, J.-H. Seo, and S. P. Pack, “Biomimetic Scaffolds of Calcium-Based Materials for Bone Regeneration,” Biomimetics, vol. 9, no. 511, pp. 1–24, 2024. https://doi.org/10.3390/biomimetics9090511.
[12] J. I. E. Zhang, Z. Zhang, D. Wang, and X. Qiang, “Study on Preparation of High-Quality Magnesium Hydroxide and Calcium Hydroxide Products from Dolomite,” JOM, pp. 1–13, 2025. https://doi.org/10.1007/s11837-025-07497-7
[13] N. H. Ahmad Shukeri, S. N. F. Syed Adam, H. Mohamad, H. Cheng Yong, and H. Yahya, “Effect of Heat Treatment on the Properties of Perlis Dolomite Powder,” Pertanika J. Sci. Technol., vol. 32, no. 3, pp. 1613–1631, 2025. https://doi.org/10.47836/pjst.33.3.23
[14] A. Namdar and E. Salahinejad, “Advances in ion-doping of Ca-Mg silicate bioceramics for bone tissue engineering,” Coord. Chem. Rev., vol. 478, 2023. https://doi.org/10.1016/j.ccr.2022.215001
[15] C. Yamagata, D. R. Leme, V. G. Rodrigues, G. T. Eretides, and A. C. Dorion Rodas, “Three routes for the synthesis of the bioceramic powder of the CaO-MgO-SiO2 system,” Ceram. Int., vol. 48, no. 7, 2022. https://doi.org/10.1016/j.ceramint.2021.12.169
[16] X. Zou, L. Fu, J. Song, G. Xu, and D. Bai, “High-temperature thermochemical conversion of iron ore tailings into diopside and akermanite-based composite materials,” Adv. Powder Technol., vol. 35, 2024.
[17] A. Najafinezhad, M. Abdellahi, H. Ghayour, A. Soheily, A. Chami, and A. Khandan, “A comparative study on the synthesis mechanism, bioactivity and mechanical properties of three silicate bioceramics,” Mater. Sci. Eng. C, vol. 72, pp. 259–267, 2017. https://doi.org/10.1016/j.msec.2016.11.084
[18] N. Balighieh, M. R. Zamani, S. F. Kashani-Bozorg, M. Kheradmandfard, M. R. Barati, and E. Mansoori, “Optimizing microwave-assisted synthesis of akermanite nanoparticles using citric acid as a chelating agent: A combined machine learning and experimental approach,” J. Mater. Res. Technol., vol. 30, no. March, pp. 2211–2222, 2024. https://doi.org/10.1016/j.jmrt.2024.03.175
[19] H. Mohammadi, Y. M. B. Ismail, K. A. Shariff, and A. F. Mohd Noor, “Microstructure evolution, grain growth kinetics and mechanical properties of Ca2MgSi2O7bioceramics sintered at various temperatures,” Process. Appl. Ceram., vol. 15, no. 4, 2021. https://doi.org/10.2298/PAC2104357M
[20] M. Assarzadehgan, I.S. Gataa, Z.Y. Abdullah, M. Kasiri-Asgarani, A. Najafinezhad, H.R. Bakhsheshi-Rad, M. Razzaghi, S. Salahshour, and D. Toghraie, “Incorporation of azithromycin into akermanite-monticellite nanocomposite scaffolds : Preparation , biological properties , and drug release characteristics,” Ceram. Int., vol. 50, no. April, pp. 43841–43853, 2024
[21] M. Ansari, F. Malmir, and A. Salati, “Preparation and characterization of akermanite/merwinite scaffolds for bone tissue repair,” J. Biomimetics, Biomater. Biomed. Eng., vol. 44, 2020. https://doi.org/10.4028/www.scientific.net/JBBBE.44.73
[22] S. Liu, T. Saidani, D. Feng, and M. Jameel, “Thermal conductivity and rheological behavior of silica / simulated body fluid – Dispersed Hardystonite and Åkermanite nanofluids : X-ray diffraction to analyze structure and morphology of a bio-ceramic,” Int. Commun. Heat Mass Transf., vol. 165, no. May, 2025.
[23] C. I. Dobriţa, A.I. Bădănoiu, G. Voicu, A.I. Nicoară, S.M. Dumitru, M.E. Puşcaşu, Ș.Chiriac, R. Ene, and F. Iordache, “Porous bioceramic scaffolds based on akermanite obtained by 3D printing for bone tissue engineering,” Ceram. Int., vol. 49, no. 22, pp. 35898–35906, 2023. https://doi.org/10.1016/j.ceramint.2023.08.270
[24] A. Peys, N. Pires Martins, F. Prado Araujo, K. Komnitsas, and P. Nielsen, “High-temperature slag engineering in pursuit of effective mineral carbonation of pyroxene-rich ferronickel slag,” J. CO2 Util., vol. 95, 2025. https://doi.org/10.1016/j.jcou.2025.103077
[25] F. Kamutzki, M. F. Bekheet, S. Schneider, A. Gurlo, and D. A. H. Hanaor, “A comparison of syntheses approaches towards functional polycrystalline silicate ceramics,” Open Ceram., vol. 9, 2022. https://doi.org/10.1016/j.oceram.2022.100241

