Experimental study on the mechanical properties of ABS-Kevlar composite specimens during high-speed FFF
Ioannis T. CHRISTODOULOU, Nikolaos E. KARKALOS, Angelos P. MARKOPOULOS
Abstract. Creation of mechanical parts by composite materials with specific requirements can be facilitated nowadays by employing additive manufacturing (AM) techniques. Especially, Fused Filament Fabrication (FFF) process is a particularly simple but effective method for this purpose for polymers and polymer composites. However, the limitations of printing speed due to the inherent characteristics of this process constrain the high levels of productivity which are necessary in industry. Thus, in this work the effect of high printing speeds on the mechanical properties of FFF-printed composite ABS-Kevlar specimens was evaluated in order to determine the potential limits of printing speed values which can be used without deteriorating the mechanical properties of specimens. Tensile and compression tests were carried out for a comprehensive range of printing speeds and the results of different mechanical properties were analyzed. The findings indicated that the increase of printing speed can affect the tensile yield strength and UTS but its influence is negligible or minimal on other mechanical properties, implying that an increase of productivity is possible, at least up to a limit, without a detrimental effect on part strength.
Keywords
High-Speed Printing, Tensile Properties, Compressive Properties, Fused Filament Fabrication, Composite Filament, Aramid Fiber
Published online 5/7/2025, 9 pages
Copyright © 2025 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Ioannis T. CHRISTODOULOU, Nikolaos E. KARKALOS, Angelos P. MARKOPOULOS, Experimental study on the mechanical properties of ABS-Kevlar composite specimens during high-speed FFF, Materials Research Proceedings, Vol. 54, pp 180-188, 2025
DOI: https://doi.org/10.21741/9781644903599-20
The article was published as article 20 of the book Material Forming
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] K. Yadav, S. Rohilla, A. Ali, M. Yadav, D. Chhabra, Effect of speed, acceleration, and jerk on surface roughness of FDM-fabricated parts, J Mater Eng Perform 33 (2024) 6998-7007. https://doi.org/10.1007/s11665-023-08476-2
[2] R.H. Sanatgar, C. Campagne, V. Nierstrasz, Investigation of the adhesion properties of direct 3D printing of polymers and nanocomposites on textiles: Effect of FDM printing process parameters, Appl Surf Sci 403 (2017) 551-563. https://doi.org/10.1016/j.apsusc.2017.01.112
[3] R. Dorado, F.J. Perez, G. Medina, F. Guerrero, Experimental measuring of printing speed in FDM, IOP Conf Ser: Mat Sci Eng 1193 (2021) 021037. https://doi.org/10.1088/1757-899X/1193/1/012037
[4] C.P.Jiang, Y.C.Cheng, H.W. Lin, Y.L. Chang, T.Pasang, S.Y. Lee, Optimization of FDM 3D printing parameters for high strength PEEK using the Taguchi method and experimental validation, Rapid Prototyp J 28(7) (2022) 1260-1271. https://doi.org/10.1108/RPJ-07-2021-0166
[5] P.Wang, B. Zou, S. Ding, L. Li, C. Huang, Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK, Chinese J Aeronaut 34(9) (2021) 236-246. https://doi.org/10.1016/j.cja.2020.05.040
[6] S.Farashi, F. Vafaee, Effect of extruder temperature and printing speed on the tensile strength of fused deposition modeling (FDM) 3D printed samples: a meta-analysis study, Int J Interact Des Manuf 16 (2022) 305-316. https://doi.org/10.1007/s12008-021-00827-4
[7] L. Auffray, P.A. Gouge, L. Hattali, Design of experiment analysis on tensile properties of PLA samples produced by fused filament fabrication, Int J Adv Manuf Technol 118 (2022) 4123-4137. https://doi.org/10.1007/s00170-021-08216-7
[8] M. Daly, M. Tarfaoui, M. Chihi, C. Bouraoui, FDM technology and the effect of printing parameters on the tensile strength of ABS parts, Int J Adv Manuf Technol 126 (2023) 5307-5323. https://doi.org/10.1007/s00170-023-11486-y
[9] R. Incesu, T. Akderya, The influence of printing speed and temperature on the mechanical, absorptive and morphological properties of PLA-based hybrid materials produced with an FDM-type 3D printer, Polymers 16(19) (2024) 2771. https://doi.org/10.3390/polym16192771
[10] M.R. Khosravani, T. Reinicke, Effects of raster layup and printing speed on strength of 3D printed structural components, Procedia Struct Integr 28 (2020) 720-725. https://doi.org/10.1016/j.prostr.2020.10.083
[11] M.S. Kamer, S. Temiz, H. Yaykasli, A. Kaya, O.E. Akay, Effect of printing speed on FDM 3d-printed PLA samples using different two printers, Int J Print Technol Digit Ind 6(3) (2022) 438-448. https://doi.org/10.46519/ij3dptdi.1088805
[12] A.A. Ansari, M. Kamil, Effect of print speed and extrusion temperature on properties of 3D printed PLA using fused deposition modeling process, Mater Today Proc 45(6) (2021) 5462-5468. https://doi.org/10.1016/j.matpr.2021.02.137
[13] P. Rezaieian, M.R. Ayatollahi, A. Nabavi-Kivi, N. Razavi, Effect of printing speed on tensile and fracture behavior of ABS specimens produced by fused deposition modeling, Eng Fract Mech 266 (2022) 108393. https://doi.org/10.1016/j.engfracmech.2022.108393
[14] A. Nabavi-Kivi, M.R. Ayatollahi, P. Rezaeian, N. Razavi, Investigating the effect of printing and mode mixity on the fracture behavior of FDM-ABS specimens. Theor ApplFract Mech 118 (2022) 103223. https://doi.org/10.1016/j.tafmec.2021.103223
[15] T.C. Yang, C.H. Yeh, Morphology and mechanical properties of 3D printed wood fiber/polylactic acid composite parts using fused deposition modeling (FDM): the effects of printing speed, Polymers 12(6) (2020) 1334. https://doi.org/10.3390/polym12061334
[16] V. Bhosale, P. Gaikwad, S. Dhere, C. Sutar, S.J. Raylar, Analysis of process parameters of 3D printing for surface finish, printing time and tensile strength, Mater Today Proc 59(1) (2022) 841-846. https://doi.org/10.1016/j.matpr.2022.01.210
[17] J. Bochnia, T. Kozior, M. Musialek, Flexural properties of thin-walled specimens with square hollow sections 3D printed from ABS reinforced with aramid fibers, Fibers 11(9) (2023) 77. https://doi.org/10.3390/fib11090077
[18] S. Rimdusit, P. Lorjai, K. Sujirote, S. Tiptipakorn, Physical and Mechanical Characteristics of Kevlar Fiber-Reinforced PC/ABS composites, Eng J 16(1), (2012) 57-66. https://doi.org/10.4186/ej.2012.16.1.57