On finishing turning of Inconel 718 using WC and CBN cutting inserts under dry conditions
Nicola Pozzato, Rachele Bertolini, Andrea Ghiotti, Stefania Bruschi
Abstract. Innovative application fields, such as aerospace, require highly reliable materials to manufacture their components, as they frequently operate under harsh conditions, such as extremely hot and abrasive environments. Nickel-based superalloys are widely employed in these applications due to their outstanding mechanical properties, which they maintain over a wide temperature range. One of the most commonly used nickel-based superalloys is Inconel 718, which exhibits a yield strength of 550 MPa, remaining nearly constant up to 760 °C. However, the very high mechanical strength of Inconel 718, coupled with its low thermal conductivity, leads to limited efficiency during machining operations in terms of tool wear acceleration, shortening the tool life and negatively affecting the machined surface quality. Cubic boron nitride (CBN) inserts have proven effective in overcoming these issues, enabling high-speed machining while ensuring acceptable workpiece quality at the same time. This paper explores the performance of CBN inserts in finishing turning of Inconel 718, compared with the coated tungsten carbide (WC) tools currently used in industrial practice. The turning experimental campaign was conducted under flood and dry conditions to evaluate the feasibility of the latter as a more sustainable alternative when machining Inconel 718. The comparison was made in terms of inserts’ life curves and wear types, degree of surface roughness achieved on the workpiece, and required cutting forces. The main key findings are: (i) the CBN inserts are less affected by adhesive phenomena compared to the WC ones but suffer from end-of-life chipping; (ii) dry turning with CBN inserts combines good productivity and a better degree of surface finish with a lower environmental impact.
Keywords
Inconel 718, Dry Turning, CBN
Published online 5/7/2025, 10 pages
Copyright © 2025 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Nicola Pozzato, Rachele Bertolini, Andrea Ghiotti, Stefania Bruschi, On finishing turning of Inconel 718 using WC and CBN cutting inserts under dry conditions, Materials Research Proceedings, Vol. 54, pp 1626-1635, 2025
DOI: https://doi.org/10.21741/9781644903599-175
The article was published as article 175 of the book Material Forming
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] Thakur DG, Ramamoorthy B, Vijayaraghavan L. Study on the machinability characteristics of superalloy Inconel 718 during high-speed turning. Materials & Design 30(5), 1718–1725. (2009) https://doi.org/10.1016/j.matdes.2008.07.017
[2] Magri A, Diniz AE, Suyama DI. 2018. Evaluating the use of high-pressure coolant in turning process of Inconel 625 nickel-based alloy. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 232(7), 1182–1192. (2018) https://doi.org/10.1177/0954405417705543
[3] Paturi UMR, et al. Progress of machinability on the machining of Inconel 718: A comprehensive review on the perception of cleaner machining. Cleaner Engineering and Technology 5, 100323. (2021) https://doi.org/10.1016/j.clet.2021.100323
[4] European Commission. The European Green Deal.
[5] Devillez A, Schneider F, Dominiak S, Dudzinski D, Larrouquere D. Cutting forces and wear in dry machining of Inconel 718 with coated carbide tools. Wear 262, 931–942. (2007) https://doi.org/10.1016/j.wear.2006.10.009
[6] Dub S, et al. Vickers hardness of diamond and CBN single crystals: AFM approach. Crystals 7(12), 369. (2017) https://doi.org/10.3390/cryst7120369
[7] Chen K, Song B, Ravichandran NK, Zheng Q, Chen X, Lee H, et al. Ultrahigh thermal conductivity in isotope-enriched cubic boron nitride. Science eaaz6149. (2020) https://doi.org/10.1126/science.aaz6149
[8] Dogra M, et al. Tool wear, chip formation and workpiece surface issues in CBN hard turning: A review. International Journal of Precision Engineering and Manufacturing 11, 341–358. (2010) https://doi.org/10.1007/s12541-010-0039-9
[9] Bushlya V, Lenrick F, Bjerke A, et al. Tool wear mechanisms of PCBN in machining Inconel 718: Analysis across multiple length scales. CIRP Annals 70(1), 73–78. (2021) https://doi.org/10.1016/j.cirp.2021.04.048
[10] Tu L, Deng Y, Zheng T, et al. Wear and friction analysis of cubic boron nitride tools with different binders in high-speed turning of nickel-based superalloys. Tribology International 173, 107659. (2022) https://doi.org/10.1016/j.triboint.2022.107659
[11] Soo S, Khan S, Aspinwall DK, et al. High-speed turning of Inconel 718 using PVD-coated PCBN tools. CIRP Annals 65(1), 89–92. (2016) https://doi.org/10.1016/j.cirp.2016.04.056
[12] Xavior MA, Patil M, Maiti A, et al. Machinability studies on Inconel 718. In: IOP Conference Series: Materials Science and Engineering. IOP Publishing, p. 012019. (2016) https://doi.org/10.1088/1757-899X/149/1/012019
[13] Criado V, Díaz-Álvarez J, Cantero JL, et al. 2018. Study of the performance of PCBN and carbide tools in finishing machining of Inconel 718 with cutting fluid at conventional pressures. Procedia CIRP 77, 634–637. (2018) https://doi.org/10.1016/j.procir.2018.08.071
[14] Cantero JL, Díaz-Álvarez J, Infante-García D, et al. High-speed finish turning of Inconel 718 using PCBN tools under dry conditions. Metals 8(3), 192. (2018) https://doi.org/10.3390/met8030192
[15] Harris TK, Brookes EJ, Taylor CJ. The effect of temperature on the hardness of polycrystalline cubic boron nitride cutting tool materials. International Journal of Refractory Metals and Hard Materials 22(2-3), 105–110. (2004) https://doi.org/10.1016/j.ijrmhm.2003.09.007
[16] Narutaki N, et al. High-speed machining of Inconel 718 with ceramic tools. CIRP Annals 42(1), 103–106. (1993) https://doi.org/10.1016/S0007-8506(07)62402-0
[17] Zeilmann RP, Fontanive F, Soares RM. Wear mechanisms during dry and wet turning of Inconel 718 with ceramic tools. The International Journal of Advanced Manufacturing Technology 92, 2705–2714. (2017) https://doi.org/10.1007/s00170-017-0327-4
[18] Jadam, T., Datta, S., & Masanta, M. (2021). Influence of cutting tool material on machinability of Inconel 718 superalloy. Machining Science and Technology, 25(3), 349-397.
[19] Bertolini R, Bedekar V, Ghiotti A, Savio E, Shivpuri R, Bruschi S., Surface integrity and corrosion performances of hardened bearing steel after hard turning. The International Journal of Advanced Manufacturing Technology 108, 1983–1995. (2016) https://doi.org/10.1007/s00170-020-05467-2
[20] Batista M, Del Sol I, Gomez-Parra A, Ramirez-Peña M, Salguero J. Study of the tool wear process in the dry turning of Al–Cu alloy. Metals 9(10), 1094. (2019) https://doi.org/10.3390/met9101094
[21] Pozzato, N., Bertolini, R., Moro, L., Ghiotti, A., Bruschi, S., & Tagarelli, L. (2025). On the wear mechanisms of ceramic round inserts in high-speed turning of Inconel 718. Wear, 205866. https://doi.org/10.1016/j.wear.2025.205866
[22] Devillez A, Le Coz G, Dominiak S, Dudzinski D. Dry machining of Inconel 718, workpiece surface integrity. Journal of Materials Processing Technology 211(10), 1590–1598. (2011) https://doi.org/10.1016/j.jmatprotec.2011.05.013.
