In-situ modal decomposition of acoustic emission events arising from low-velocity impacts
Jaslyn Gray, Cedric Rosalie, Ben Vien, Wing Kong Chiu, Nik Rajic
Abstract. In the field of structural health monitoring (SHM), it is common to employ the use of sensors to provide information about the state of a platform, particularly when concerned with whether damage has occurred as a result of impact. Acoustic emission (AE) sensing using piezoelectric elements is well suited to the detection of guided plate waves arising from impact events on thin-walled aerospace structures. This paper presents a systematic evaluation of impact induced AE with increasing velocity and explores changes in the resulting signals model content. A spring-loaded mechanism is used to accelerate ball bearings up to 7 m/s and the corresponding AE event is recorded using a LAMDA (Linear Array for Modal Decomposition and Analysis) sensor. This LAMDA sensor is an in-situ sensing capability that allows for frequency-wavenumber decomposition of the acquired acoustic signal into its constituent modes, which can then be mapped against theoretical dispersion curves for the material under investigation. To date, most research in the low velocity regime is concerned with the fundamental antisymmetric (A0) and symmetric (S0) wave modes from multiple sensing locations. Using LAMDA, it is possible to build a more complete picture of an impact signal, not currently achievable with conventional sensing methods.
Keywords
Modal Decomposition, Acoustic Emission, Damage Detection, Piezo-Electric Sensing, Low-Velocity Impact
Published online 3/25/2025, 6 pages
Copyright © 2025 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Jaslyn Gray, Cedric Rosalie, Ben Vien, Wing Kong Chiu, Nik Rajic, In-situ modal decomposition of acoustic emission events arising from low-velocity impacts, Materials Research Proceedings, Vol. 50, pp 127-132, 2025
DOI: https://doi.org/10.21741/9781644903513-15
The article was published as article 15 of the book Structural Health Monitoring
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] M. Senthilkumar, T.G. Sreekanth and S.M Reddy. “Nondestructive health monitoring techniques for composite materials: A review,” Polymers and Polymer Composites, vol. 29 (5), pp. 528-540, 2021. https://doi.org/10.1177/0967391120921701
[2] S. Khalid, J. Song, M.M. Azad, M.U. Elahi, J. Lee, S. Jo, H.S. Kim, “A comprehensive Review of Emerging Trends in Aircraft Structural Prognostics and Health Management,” Mathematics, vol. 11 (18) 3837, 2023. https://doi.org/10.3390/math11183837
[3] V. Giurgiutiu, “6.4 Lamb waves,” in Structual health monitoring: with piezoelectric wafer active sensors, Academic Press. Elsevier, 2008, pp. 198-228.
[4] D. Alleyne and P. Cawley. ‘A two-dimensional Fourier transform method for the measurements of propagating multimode signals.’ The Journal of the Acoustical Society of America, vol. 89 (3), pp. 1159-1168, 1991. https://doi.org/10.1121/1.400530
[5] C. Rosalie, N. Rajic, S. van der Velden, F. Rose, J. Smithard and W.K. Chiu, “Towards composite damage classification using in situ wavenumber-frequency modal decomposition of Acoustic Emissions,” in European Workshop on Structural Health Monitoring. EWSHM 2020. P. Rizzo, A. Milazzo (eds). Lecture Notes in Civil Engineering, vol 127. Springer, Cham, 2021. https://doi.org/10.1007/978-3-030-64594-6_63
[6] N. Rajic, C. Rosalie, BS. Vien, S. van der Velden, LRF. Rose, J. Smithard and WK. Chiu. “In situ wavenumber-frequency modal decomposition of acoustic emission,” Structural Health Monitoring, vol. 19 (6), pp. 2033-2050, 2020. https://doi.org/10.1177/1475921719885324
[7] N. Rajic, C. Rosalie, S. van der Velden, et al. “A flexible high density piezoelectric sensor array for in situ modal decomposition,” in Proceedings of the 9th European Workshop on Structural Health Monitoring, Manchester, 2018.
[8] J. Zhu, S.M. Parvasi, S.C.M. Ho, D. Patil, M. Ge, H. Li and G. Song, “An innovative method for automatic determination of time of arrival for lamb wave excited by impact events,” Smart Materials and Structures, vol. 26, 2017. https://doi.org/10.1088/1361-665X/aa63e1
[9] L. Capineri and A. Bulletti, “A versatile analog electronic interface for piezoelectric sensors used for impacts detection and positioning in Structural Health Monitoring (SHM) systems,” Electronics, vol. 10, 1047, 2021. https://doi.org/10.3390/electronics10091047
[10] S. Guo, H. Ding, Y. Li, H. Feng, X. Xiong, Z. Su and W. Feng, “A hierarchical deep convolutional regression framework with sensor network fail-safe adaption for acoustic-emission- based structural monitoring,” Mechanical Systems and Signal Processing, vol. 181, 2022. https://doi.org/10.1016/j.ymssp.2022.109508
[11] N. Daniele Boffa, N. Area, E. Manaco, M. Viscardi, F. Ricci and T. Kundu, “About the combination of high and low frequency methods for impact detection on aerospace components,” Progress in Aerospace Sciences, vol. 129, 2022. https://doi.org/10.1016/j.paerosci.2021.100789
[12] Pavlakovic, B., M.J.S. Lowe, D. Alleyne, and P. Cawley, Disperse: A General Purpose Program for Creating Dispersion Curves, in Review of Progress in Quantitative Nondestructive Evaluation, D. Thompson and D. Chimenti, Editors. 1997, Springer: US. pp. 185-192. https://doi.org/10.1007/978-1-4615-5947-4_24
