Design, analysis and topology optimization of a car’s suspension lower control arm
Nikolaos MANINAS, Ioannis PAPANTONIOU, Nikolaos VAXEVANIDIS
Abstract. The modern automotive industry aims to design durable yet lightweight components that meet high performance and material efficiency goals, utilizing technologies like metal 3D printing. This study focuses on the design, analysis, and topology optimization of a MacPherson-type lower control arm, with a particular emphasis on static analysis and mass reduction achieved through topology optimization. The design process began with reverse engineering an existing control arm to acquire basic dimensions, followed by the development of a new model in SolidWorks. SolidWorks Simulation tools were employed for both stress analysis and topology optimization. The analysis considered the four primary stress forces, applied both parallel and perpendicular to the vehicle’s longitudinal axis. The forces were calculated using basic mechanics and vehicle dynamics formulas, and the results were examined through finite element analysis (FEA), capturing Von Mises stresses. The selected materials were aluminum 7075-T6 and titanium Ti-6Al-4V, both suitable for 3D printing. The highest stresses (196 MPa) occurred during braking at maximum speed, and based on this scenario, topology optimization was performed. The optimized arm achieved a mass reduction of 38% compared to the non-optimized model, with SolidWorks Simulation used to evaluate mass reduction, strength retention, and fatigue analysis based on material type, underscoring the benefits of this approach.
Keywords
Control Arm Design, Material Selection, Static Analysis, Topology Optimization, Metal 3D Printing, Fatigue Analysis
Published online 12/10/2024, 12 pages
Copyright © 2024 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Nikolaos MANINAS, Ioannis PAPANTONIOU, Nikolaos VAXEVANIDIS, Design, analysis and topology optimization of a car’s suspension lower control arm, Materials Research Proceedings, Vol. 46, pp 393-404, 2024
DOI: https://doi.org/10.21741/9781644903377-50
The article was published as article 50 of the book Innovative Manufacturing Engineering and Energy
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] Kale A, Tadamalle A, Patti N. Analysis and Optimization of Lower Control Arm. Evolutions in Mechanical Engineering 2018;1. https://doi.org/10.31031/EME.2018.01.000505
[2] Rahman MHA, Salleh MS, Mohd MS, Kamal MRM, Marjom Z, Anuar L, et al. Design and Optimization of Front Lower Control Arm (FLCA) for C-Segment Passenger Car. International Journal of Engineering & Technology 2018;7:71–5. https://doi.org/10.14419/IJET.V7I3.17.16625
[3] Dhanu G, Kattimani RS. Comparision study of lower control arm with different material. International Research Journal of Engineering and Technology (IRJET) 2016;03
[4] Song T, Xu S, He S. Analysis of material selection trend of the automobile control arm. J Phys Conf Ser 2022;2390. https://doi.org/10.1088/1742-6596/2390/1/012046
[5] Aboulkhair NT, Simonelli M, Parry L, Ashcroft I, Tuck C, Hague R. 3D printing of Aluminium alloys: Additive Manufacturing of Aluminium alloys using selective laser melting. Prog Mater Sci 2019; 106:100578. https://doi.org/10.1016/J.PMATSCI.2019.100578
[6] Jhinkwan A, Kalsi S, Pankaj. An Overview on 3d Metal Printing Technology in Automobile Industry. AIP Conf Proc 2023;2558. https://doi.org/10.1063/5.0120028/2873967
[7] Ling Y, Li A, Liu R, Gauthier S, Abarzhi SI, Sreenivasan KR, et al. Lightweight design of an automotive lower control arm using topology optimization for forming process. IOP Conf Ser Mater Sci Eng 2021;1157:012083. https://doi.org/10.1088/1757-899X/1157/1/012083
[8] Pachapuri MSA, Lingannavar RG, Kelageri NK, Phadate KK. Design and analysis of lower control arm of suspension system. Mater Today Proc 2021;47:2949–56. https://doi.org/10.1016/J.MATPR.2021.05.035
[9] Gillespie T. D. Fundamentals of Vehicle Dynamics, Revised Edition. Pennsylvania, USA: SAE International; 2021.
[10] Wong JY. Theory of ground vehicles. Third Edition. Ottawa, Canada: John Wiley & Sons Inc.; 2001.
[11] Rajamani R. Vehicle Dynamics and Control. Second Edition. Boston, MA: Springer US; 2012. https://doi.org/10.1007/978-1-4614-1433-9
[12] Milliken WF., Milliken DL. Race car vehicle dynamics. Warrendale, Pennsylvania, USA: SAE International; 1995.
