Superplastic microstructure characteristics and unified constitutive model of TA32 titanium alloy

Superplastic microstructure characteristics and unified constitutive model of TA32 titanium alloy

LIU Yang, WANG Chunhui, LI Zhiqiang, ZHANG Ning, ZHAO Bing, SUN Chaoyang

download PDF

Abstract. The superplastic deformation behavior and microstructure characteristics of TA32 titanium alloy were studied at different deformation temperatures (920-960°C) and initial strain rates (1×10-3-3×10-3 s-1). A unified constitutive model was developed and coupled with internal state variables. Results show that TA32 alloy featured steady flow stress and uniform plastic deformability under the dynamic equilibrium between softening and hardening effects. Increasing temperature and strain induced α→β phase transformation and α grain growth. Dislocation accumulation and grain boundary migration formed the dynamic recovery (DRV) and dynamic recrystallization (DRX) mechanisms. Using dislocation density, the proposed unified constitutive model built a quantitative relationship between superplastic flow stress and internal state variables such as grain size, with the correlation coefficient R, average absolute relative error (AARE), and root mean square error (RMSE) between the predicted and experimental stress values being 0.98, 6.91%, and 1.94, respectively. The unified constitutive model could predict well the flow stress and grain size evolution of TA32 titanium alloy during superplastic deformation.

Keywords
TA32 Titanium Alloy, Superplasticity, Deformation Characteristics, Constitutive Model

Published online 9/15/2024, 11 pages
Copyright © 2024 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: LIU Yang, WANG Chunhui, LI Zhiqiang, ZHANG Ning, ZHAO Bing, SUN Chaoyang, Superplastic microstructure characteristics and unified constitutive model of TA32 titanium alloy, Materials Research Proceedings, Vol. 44, pp 79-89, 2024

DOI: https://doi.org/10.21741/9781644903254-9

The article was published as article 9 of the book Metal Forming 2024

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

References
[1] S. Li, T.S. Deng, Y.H. Zhang, Y.Q. Liang, R.X. Li, T.H. Dong, Review on the creep resistance of high-temperature titanium alloy, Trans. Indian Inst. Met. 74 (2021) 215-222. https://doi.org/10.1007/s12666-020-02137-x
[2] C. Cheng, Y. Feng, Z.Y. Chen, H.E. Li, Q.J. Wang, X. Wang, Effect of annealing temperature on microstructure, texture and tensile properties of TA32 sheet, Mater. Sci. Eng. A 826 (2021) 141971. https://doi.org/10.1016/j.msea.2021.141971
[3] B. Babu, L.E. Lindgren, Dislocation density based model for plastic deformation and globularization of Ti-6Al-4V, Int. J. Plast. 50 (2013) 94-108. https://doi.org/10.1016/j.ijplas.2013.04.003
[4] Y.W. Xiao, Y.C. Lin, Y.Q. Jiang, X.Y. Zhang, G.D. Pang, D. Wang, K.C. Zhou, A dislocation density-based model and processing maps of Ti-55511 alloy with bimodal microstructures during hot compression in α+β region, Mater. Sci. Eng., A 790 (2020) 139692. https://doi.org/10.1016/j.msea.2020.139692
[5] Q. Bai, J. Lin, T.A. Dean, D.S. Balint, T. Gao, Z. Zhang, Modelling of dominant softening mechanisms for Ti-6Al-4V in steady state hot forming conditions, Mater. Sci. Eng. A 559 (2013) 352-358. https://doi.org/10.1016/j.msea.2012.08.110
[6] T. Yasmeen, Z.T. Shao, L. Zhao, P. Gao, J. Lin, J. Jiang, Constitutive modeling for the simulation of the superplastic forming of TA15 titanium alloy, Int. J. Mech. Sci. 164 (2019) 105178. https://doi.org/10.1016/j.ijmecsci.2019.105178
[7] Y. Liu, Z.Q. Li, B. Zhao, T. Yang, C.Y. Sun, Superplastic deformation behavior and constitutive model of TA32 titanium alloy, Rare Metal Mat. Eng. 51 (2022) 3752-3761.
[8] J.W. Xu, W.D. Zeng, Q.Y. Zhao, D.D. Zhou, S.T. He, R.C. Jia, X.F. Zhou, Analysis of deformation behavior and microstructure of a near-alpha titanium alloy in single phase region, Mater. Sci. Eng. A 803 (2021) 140723. https://doi.org/10.1016/j.msea.2020.140723
[9] Y. Liu, Z.Q. Li, B. Zhao, C.y. Sun, Y.h. Feng, Microstructure evolution characteristics of near-α TA32 titanium alloy during superplastic tensile deformation, Mater. Sci. Eng., A 879 (2023) 145264. https://doi.org/10.1016/j.msea.2023.145264
[10] L. Despax, V. Vidal, D. Delagnes, M. Dehmas, H. Matsumoto, V. Velay, Influence of strain rate and temperature on the deformation mechanisms of a fine-grained Ti-6Al-4V alloy, Mater. Sci. Eng. A 790 (2020) 139718. https://doi.org/10.1016/j.msea.2020.139718
[11] J. Lin, T.A. Dean, Modelling of microstructure evolution in hot forming using unified constitutive equations, J. Mater. Process. Technol. 167 (2005) 354-362. https://doi.org/10.1016/j.jmatprotec.2005.06.026
[12] L. Yang, B.y. Wang, G. Liu, H.j. Zhao, J. Zhou, Hot tensile behavior and self-consistent constitutive modeling of TA15 titanium alloy sheets, J. Mater. Eng. Perform. 24 (2015) 4647-4655. https://doi.org/10.1007/s11665-015-1784-7
[13] J. Lin, M. Mohamed, D. Balint, T.A. Dean, The development of continuum damage mechanics-based theories for predicting forming limit diagrams for hot stamping applications, Int. J. Damage Mech. 23 (2013) 684-701. https://doi.org/10.1177/1056789513507731
[14] J. Lin, Y. Liu, D.C.J. Farrugia, M. Zhou, Development of dislocation-based unified material model for simulating microstructure evolution in multipass hot rolling, Philos. Mag. 85 (2005) 1967-1987. https://doi.org/10.1080/14786430412331305285
[15] J. Lin, Y. Liu, T.A. Dean, A review on damage mechanisms, models and calibration methods under various deformation conditions, Int. J. Damage Mech. 14 (2016) 299-319. https://doi.org/10.1177/1056789505050357
[16] E. Alabort, P. Kontis, D. Barba, K. Dragnevski, R.C. Reed, On the mechanisms of superplasticity in Ti-6Al-4V, Acta Mater. 105 (2016) 449-463. https://doi.org/10.1016/j.actamat.2015.12.003
[17] W. Roberts, B. Ahlblom, A nucleation criterion for dynamic recrystallization during hot working, Acta Mater. 26 (1978) 801-813. https://doi.org/10.1016/0001-6160(78)90030-5
[18] R. Sandström, R. Lagneborg, A model for hot working occurring by recrystallization, Acta Mater. 23 (1975) 387-398. https://doi.org/10.1016/0001-6160(75)90132-7
[19] J. Lin, A set of unified constitutive equations for modelling microstructure evolution in hot deformation, J. Mater. Process. Technol. 143-144 (2003) 281-285. https://doi.org/10.1016/s0924-0136(03)00472-2