Surface integrity analysis of 304 stainless steel after slurry blasting

–

Surface integrity analysis of 304 stainless steel after slurry blasting

CHAI Ze-lin, ZHOU Cun-long, GUO Rui, JIANG Zhengyi

Abstract. The Eco Pickled Surface technology has attracted increasing attention due to its green and environmentally friendly characteristics. However, due to the complex internal structure of the oxide skin and the diverse bonding methods with the substrate surface, as well as the failure to establish a relationship between the substrate surface integrity and process parameters after descaling, the widespread application of this technology is restricted. The 304 stainless steel hot-rolled plates and strips had been researched in this article, and the finite element ANSYS/AUTODYN modules had been used to simulate the descaling process; An analysis was conducted on the surface integrity of 304 stainless steel after descaling, including roughness, residual stress, and corrosion resistance. The results showed that: The maximum temperature on the substrate surface under different abrasive particle sizes, blasting speeds, and blasting angles is 95℃;the impact range and depth of the substrate surface after slurry blast will increase with the increase of abrasive particle size and injection speed, The maximum hardened layer after slurry impact is 140 μm; The minimum corrosion current density on the substrate surface after slurry impact can reach 1.29*10-6A/cm2, the corrosion resistance of the substrate surface has been significantly improved, and the EBSD results show that the grains after slurry impact are concentrated in 4-19 μm, maximum 22 μm. The average grain size is 10.79 μm.

Keywords
Slurry Blasting, Surface Integrity, Surface Roughness, Residual Stress, Corrosion Resistance

Published online 9/15/2024, 15 pages
Copyright © 2024 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: CHAI Ze-lin, ZHOU Cun-long, GUO Rui, JIANG Zhengyi, Surface integrity analysis of 304 stainless steel after slurry blasting, Materials Research Proceedings, Vol. 44, pp 167-181, 2024

DOI: https://doi.org/10.21741/9781644903254-19

The article was published as article 19 of the book Metal Forming 2024

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

References
[1] K. Voges, A. Mueth, Eco-pickled surface：an environmentally advantageous alternative to conventional acid pickling, Iron Steel Technol. 4 (2008) 81-96.
[2] J.G.A. Bitter, A study of erosion phenomena: Part I, Wear 6 (1963) 5-21. https://doi.org/10.1016/0043-1648(63)90003-6
[3] J.G.A. Bitter, A study of erosion phenomena: Part Ⅱ, Wear 6 (1963) 169-190. https://doi.org/10.1016/0043-1648(63)90073-5
[4] C. Zhang, Y. Zhang, F. Zhang, D. Luan, Study on Removal Model of Abrasive Waterjet Machining, J. Mech. Eng. 51 (2015) 188-196. https://doi.org/10.3901/JME.2015.07.188
[5] J. Li, A. Du, Y. Fan, X. Zhao, R. Ma, J. Wu, Effect of shot-blasting pretreatment on microstructures of hot-dip galvanized coating, Surf. Coat. Tech. 4 (20190 218-224. https://doi.org/10.1016/j.surfcoat.2019.02.075
[6] Ramprasad, G. Upadhyay, K. Hassan, Optimization MRR Of stainless steel 403 in abrasive water jet machining using Anova and Taguchi method, Int. J. Eng. Res. Appl. 5 (2015) 86-91.
[7] K. Voges, A. Mueth, Eco-pickled surface：an environmentally advantageous alternative to conventional acid pickling, Iron Steel Technol. 4 (2008) 81-96.
[8] C. Fengjun, A review of research on abrasive jet surface polishing, Surf. Technol. 44 (2015) 119-123. https://doi.org/10.16490/j.cnki.issn.1001-3660.2015.11.019
[9] V. Chaturvedi, D. Singh, Mutli Response optimization of process parameters of abrasive water jet machining for stainless steel AISI 304 using VIKOR approach coupled with signal to noise ratio mechnology, J. Adv. Manuf. Syst. 14 (2015) 107-121. https://doi.org/10.1142/S0219686715500080
[10] S.R. Lohar, P.R. Kubade. Current research and development in abrasive water jet machining (AWJM): A Review, Int. J. Sci. Res. 5 (2016) 996-999.
[11] B. Levy, M. EI Mansori, M. El Hadrouz, S. Mezghani, A.-L. Beaudonnet, J. Cabrero, Smart tribo-peening process for surface functionalization through digital twin concept, Adv. Manuf. Technol. 4 (2021) 1-23. https://doi.org/10.1007/s00170-021-07143-x
[12] N. Minhas, A. Thakur, S. Mehlwal, Multi‑variable Optimization of the Shot Blasting of Additively Manufactured AlSi10Mg Plates for Surface Roughness Using Response Surface Methodology, Arabian J. Sci. Eng. 4 (2021) 1-15.
[13] Z. Li, F. Yang, Y. Liu, Y. Gao, Numerical Simulation of Derusting Treatment of Steel Parts By Shot Blast, CMES 120 (2019) 486-500. https://doi.org/10.32604/cmes.2019.05187
[14] P. Moonchaleanporn, S. Songkuea, J. Klanpolrang, P. Payaksak, K. Wongpinkaew, N. Bunchoo, E. Viyanit, A. Manonukul, Improving corrosion resistance in sintered 304L stainless steel using shot blasting, Int. J. Mater. Product Technol. 59 (2019) 172-191. https://doi.org/10.1504/IJMPT.2019.102643
[15] G. Singh, S. Singh, C. Prakash, S. Ramakrishna, On investigating the soda-lime shot blasting of AZ31 alloy: Effects on surface roughness, material removal rate, corrosion resistance, and bioactivity, J. Magnesium Alloy. 9 (2021) 1272-1284. https://doi.org/10.1016/j.jma.2020.11.017
[16] U. Oberste-Lehn, C. Beamer, P. Gümpel, A. Karl, Corrosion resistance of low-temperature, surface-hardened stainless steel, Mater. Perform. 58 (2019) 42-46.
[17] X. Zhang, Mechanism and Experimental Study on Surface Oxidation Skin Rupture of Q235 Strip Steel, Taiyuan University of science and technology, 2016.
[18] D. Bian, Research on the critical fracture stress of Q235 oxide scale, Taiyuan University of science and technology, 2013.
[19] M. Parsi, K. Najmi, F. Najafifard, S. Hassani, B.S. McLaury, S.A. Shirazi, A comprehensive review of solid particle erosion modeling for oil and gas wells and pipelines applications, J. Natural Gas Sci. Eng. 21 (2014) 850-873. https://doi.org/10.1016/j.jngse.2014.10.001
[20] S. Wang, Simulation and Experimental Study on Shot Blasting Impact Process for Acid Free Descaling of Rolled Strip Steel, Beijing: University of Science and Technology Beijing, 2018.
[21] L. Zhai, Mechanism, Evaluation and Application of Shot Blasting Strengthening, Heat Treat. Tech. Equip. 29 (2008) 53-66.
[22] F. Chen, W. Ge, Review of smooth particle hydrodynamics methods for multiphase flow, J. Mech 53 (2021) 1-17.
[23] W.B. Rowe, M.N. Morgan, S.C.E. Black, B. Mills, A simplified approach to control of thermal damage in grinding, CIRP annals 45 (1996) 299-302. https://doi.org/10.1016/S0007-8506(07)63067-4
[24] Z. Yu, Study on the influence of shape and position characteristics of abrasive particles and their proportions on the thermodynamic coupling process of grinding, Liaoning: Northeastern University, 2019.
[25] H. Yang, Study on Preparation and Properties of Sol gel Anticorrosive Coating on Aluminum Alloy, Xi’an University of technology, 2021.
[26] Y. Wang, Overview of research on pitting corrosion of stainless steel, Corros. Sci. Protect. Tech. 27 (2015) 387-392.