Recent advances in development, characterization and joining of new sustainable materials
DOINA BANEA Mariana, FERNANDES MEDEIROS DE QUEIROZ Henrique, DE SOUZA E SILVA NETO Jorge, KIOSHI KAWASAKI CAVALCANTI Daniel
download PDFAbstract. Nowadays, in order to increase the transport efficiency and reduce fuel consumption and emissions of contaminants, a reduction in weight associated with improved safety performance of the materials in use must be achieved. On the other hand, environmental concern has generated interest in research about new materials aligned with the principles of sustainability. Thus, this need for better performing and ecological structures has resulted in the development of a new variety of materials. Among these materials, currently, are the composites produced from resources of renewable sources. Natural fiber composites have recently attracted a great deal of attention by the industry due to their many attractive benefits (e.g., high strength-to-weight ratio, sustainable characteristics and low cost). Welding is highly impractical to use in these situations (i.e., thermoset polymer composites) and rivets or screws exhibit stress concentrations and offer a low fatigue resistance. Adhesive bonding is usually the preferred method since it allows for greater flexibility in design and is more efficient in mechanical and energy aspects. In this work, recent advances in development, characterization and joining of new sustainable materials, critical challenges and future perspectives are presented. The application of sustainable green composites may further increase in many structural and non-structural applications if their joining behavior is well-known and established.
Keywords
Composite Materials, Hybrid Composites, Natural Fibers, Synthetic Fibers, Sustainable Materials, Mechanical Characterization, Adhesive Bonded Joints
Published online 4/24/2024, 10 pages
Copyright © 2024 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: DOINA BANEA Mariana, FERNANDES MEDEIROS DE QUEIROZ Henrique, DE SOUZA E SILVA NETO Jorge, KIOSHI KAWASAKI CAVALCANTI Daniel, Recent advances in development, characterization and joining of new sustainable materials, Materials Research Proceedings, Vol. 41, pp 530-539, 2024
DOI: https://doi.org/10.21741/9781644903131-59
The article was published as article 59 of the book Material Forming
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] J. Neto, H. Queiroz, R. Aguiar, R. Lima, D. Cavalcanti, M. D. Banea, A review of recent advances in hybrid natural fiber reinforced polymer composites, J. Renew. Mater. 10, (2022) 561-589. https://doi.org/10.32604/jrm.2022.017434
[2] K. L. Pickering, M. A. Efendy, T. M. Le, A review of recent developments in natural fibre composites and their mechanical performance, Compos. – A: Appl. Sci. 83, (2016) 98-112.
[3] B. Ravishankar, S. K. Nayak, M. A. Kader, Hybrid composites for automotive applications – A review, J. Reinf. Plast. Compos. 38, (2019) 835-845. https://doi.org/10.1177/0731684419849708
[4] H. F. M. de Queiroz, M. D. Banea, D. K. K. Cavalcanti, Experimental analysis of adhesively bonded joints in synthetic- and natural fibre-reinforced polymer composites, J. Compos. Mater. 54, (2020) 1245-1255. https://doi.org/10.1177/0021998319876979
[5] J. S. S. Neto, H. F. M. de Queiroz, R. A. A. Aguiar, M. D. Banea, A review on the thermal characterisation of natural and hybrid fiber composites, Polym. 13, (2021) https://doi.org/10.3390/polym13244425
[6] D. K. K. Cavalcanti, M. D. Banea, J. S. S. Neto, R. A. A. Lima, Comparative analysis of the mechanical and thermal properties of polyester and epoxy natural fibre-reinforced hybrid composites, J. Compos. Mater. 55, (2021) 1683-1692. https://doi.org/10.1177/0021998320976811
[7] V. Chauhan, T. Kärki, J. Varis, Review of natural fiber-reinforced engineering plastic composites, their applications in the transportation sector and processing techniques, J. Thermoplast. Compos. Mater. 35, (2022) 1169-1209.
[8] U. K. Sanivada, G. Mármol, F. P. Brito, R. Fangueiro, PLA Composites Reinforced with Flax and Jute Fibers—A Review of Recent Trends, Processing Parameters and Mechanical Properties, Polym. 12, (2020) 2373.
[9] H. Ku, H. Wang, N. Pattarachaiyakoop, M. Trada, A review on the tensile properties of natural fiber reinforced polymer composites, Compos. B. Eng. 42, (2011) 856-873. https://doi.org/10.1016/j.compositesb.2011.01.010
[10] R. de Araujo Alves Lima, D. Kawasaki Cavalcanti, J. de Souza e Silva Neto, H. Meneses da Costa, M. D. Banea, Effect of surface treatments on interfacial properties of natural intralaminar hybrid composites, Polym. Compos. 41, (2020) 314-325. https://doi.org/10.1002/pc.25371
[11] Y. Swolfs, L. Gorbatikh, I. Verpoest, Fibre hybridisation in polymer composites: A review, Compos. – A: Appl. Sci. 67, (2014) 181-200. https://doi.org/10.1016/j.compositesa.2014.08.027
[12] H. F. M. de Queiroz, M. D. Banea, Methods to increase the mechanical performance of composite adhesive joints: An overview with focus on joints with natural fibre composite adherends, Journal of Composite Materials. 56, (2022) 3993-4010. https://doi.org/10.1177/00219983221125906
[13] M. D. Banea, J. S. S. Neto, D. K. K. Cavalcanti, “Recent Trends in Surface Modification of Natural Fibres for Their Use in Green Composites,” in Materials Horizons: From Nature to Nanomaterials, ed, 2021, pp. 329-350.
[14] J. S. S. Neto, R. A. A. Lima, D. K. K. Cavalcanti, J. P. B. Souza, R. A. A. Aguiar, M. D. Banea, Effect of chemical treatment on the thermal properties of hybrid natural fiber-reinforced composites, J. Appl. Polym. Sci. 136, (2019). https://doi.org/10.1002/app.47154
[15] H. Fernandes Medeiros de Queiroz, M. D. Banea, D. Kioshi Kawasaki Cavalcanti, J. de Souza e Silva Neto, The effect of multiscale hybridization on the mechanical properties of natural fiber-reinforced composites, J. Appl. Polym. Sci. 138, (2021) 10.1002/app.51213
[16] J. S. S. Neto, M. D. Banea, D. K. K. Cavalcanti, H. F. M. Queiroz, R. A. A. Aguiar, Analysis of mechanical and thermal properties of epoxy multiwalled carbon nanocomposites, J. Compos. Mater. 54, (2020) 4831-4840. https://doi.org/10.1177/0021998320939232
[17] J. S. S. Neto, H. F. M. de Queiroz, D. K. K. Cavalcanti, R. A. A. Aguiar, A. B. Pereira, M. D. Banea, Effect of ultraviolet radiation and water spraying on the mechanical properties of multi-walled carbon nanotubes reinforced natural fiber and hybrid composites, J. Appl. Polym. Sci. 139, (2022) 10.1002/app.51915
[18] V. Prasad, K. Sekar, M. A. Joseph, Mechanical and water absorption properties of nano TiO2 coated flax fibre epoxy composites, Constr Build Mater. 284, (2021) 122803. https://doi.org/10.1016/j.conbuildmat.2021.122803
[19] J. S. S. Neto, D. K. K. Cavalcanti, L. E. da Cunha Ferro, H. F. M. de Queiroz, R. A. A. Aguiar, M. D. Banea, Effect of Multi-Walled Carbon Nanotubes on the Mechanical and Thermal Properties of Curauá Natural-Fiber-Reinforced Composites, C. 9, (2023) 102.
[20] M. D. Banea, Natural Fibre Composites and Their Mechanical Behaviour, Polym. 15, (2023). https://doi.org/10.3390/polym15051185
[21] D. K. K. Cavalcanti, M. D. Banea, J. S. S. Neto, R. A. A. Lima, L. F. M. da Silva, R. J. C. Carbas, Mechanical characterization of intralaminar natural fibre-reinforced hybrid composites, Compos. B. Eng. 175, (2019). https://doi.org/10.1016/j.compositesb.2019.107149
[22] A. L. Pereira, M. D. Banea, A. B. Pereira, Effect of intralaminar hybridization on mode I fracture toughness of natural fiber-reinforced composites, J BRAZ SOC MECH SCI. 42, (2020). https://doi.org/10.1007/s40430-020-02525-w
[23] A. L. Pereira, M. D. Banea, J. S. S. Neto, D. K. K. Cavalcanti, Mechanical and thermal characterization of natural intralaminar hybrid composites based on sisal, Polym. 12, (2020). https://doi.org/10.3390/POLYM12040866
[24] H. F. M. de Queiroz, R. H. A. Rosa, J. S. S. Neto, D. K. K. Cavalcanti, M. D. Banea, Mechanical characterization of short Curauá/glass fiber-reinforced interlaminar hybrid composite adhesive joints, J Adhes Sci Technol. 2023). https://doi.org/10.1080/01694243.2023.2261263
[25] H. F. M. de Queiroz, M. D. Banea, D. K. K. Cavalcanti, Adhesively bonded joints of jute, glass and hybrid jute/glass fibre-reinforced polymer composites for automotive industry, Appl. Adhes. Sci. 9, (2021) 2. https://doi.org/10.1186/s40563-020-00131-6
[26] H. F. M. de Queiroz, J. S. S. Neto, D. K. K. Cavalcanti, M. D. Banea, A novel 3D fibre-reinforcement architecture for high performance natural fibre reinforced composite adhesively bonded joints, J Adhes. 100, (2024) 118-138. https://doi.org/10.1080/00218464.2023.2200173
[27] D. K. K. Cavalcanti, M. D. Banea, H. F. M. de Queiroz, Mechanical Characterization of Bonded Joints Made of Additive Manufactured Adherends, Ann. Dunarea Jos” Univ. Galati Fascicle XII Weld. Equip. 30, (2019) 27-33. https://doi.org/10.35219/awet.2019.04
[28] D. K. K. Cavalcanti, M. D. Banea, H. F. M. de Queiroz, Effect of material on the mechanical properties of additive manufactured thermoplastic parts, Ann. Dunarea Jos” Univ. Galati Fascicle XII Weld. Equip. 31, (2020) 5-12. https://doi.org/10.35219/awet.2020.01
[29] D. K. K. Cavalcanti, H. F. M. de Queiroz, M. D. Banea, Performance enhancement of adhesive joints of additive manufactured parts by using different types of fibre reinforcements, Int. J. Adhes. 124, (2023). https://doi.org/10.1016/j.ijadhadh.2023.103371
[30] D. K. K. Cavalcanti, H. F. M. de Queiroz, J. S. S. Neto, M. D. Banea, Strengthening of additive manufactured parts by using different type of fibre reinforcements, Int. J. Adv. Manuf. Technol. 123, (2022) 1889-1903. https://doi.org/10.1007/s00170-022-10327-8
[31] D. K. K. Cavalcanti, J. S. S. Neto, H. F. M. D. Queiroz, Y. Wu, V. F. S. Neto, M. D. Banea, Development and Mechanical Characterization of Short Curauá Fiber-Reinforced PLA Composites Made via Fused Deposition Modeling, Polym. 14, (2022). https://doi.org/10.3390/polym14225047
[32] A. C. de Mendonça, D. K. K. Cavalcanti, H. F. M. de Queiroz, J. S. S. Neto, F. J. P. Chaves, M. D. Banea, MECHANICAL CHARACTERIZATION OF FILLER MODIFIED ABS 3D PRINTED COMPOSITES MADE VIA FUSED FILAMENT FABRICATION, Ann. Dunarea Jos” Univ. Galati Fascicle XII Weld. Equip. 33, (2022) 27-34. https://doi.org/10.35219/awet.2022.02
[33] N. V. Santos, D. C. T. Cardoso, 3D printing of vegetable yarn-reinforced polymer components, J. Clean. Prod. 415, (2023) 137870. https://doi.org/10.1016/j.jclepro.2023.137870
[34] P. Boisse, R. Akkerman, P. Carlone, L. Kärger, S. V. Lomov, J. A. Sherwood, Advances in composite forming through 25 years of ESAFORM, Int. J. Mater. Form. 15, (2022) 39. 10.1007/s12289-022-01682-8
[35] Y. Singh, J. Kumar, I. Singh, P. K. Rakesh, “Joining behavior of natural fiber reinforced polymer composites,” in Joining Processes for Dissimilar and Advanced Materials, ed, 2021, pp. 33-63.
[36] G. B. de Seixas, H. F. M. de Queiroz, J. S. S. Neto, M. D. Banea, Effect of water on the mechanical and thermal properties of natural fibre reinforced hybrid composites, J. Compos. Mater. 57, (2023) 1941-1958. https://doi.org/10.1177/00219983231166570
