Heterogeneity of strain and texture inside roll-bonded multilaminates

–

Heterogeneity of strain and texture inside roll-bonded multilaminates

HANON Guillaume, MALET Loïc, DELANNAY Laurent

Abstract. This study demonstrates the usefulness of crystal plasticity modeling and crystallographic texture analysis when aiming to understand through-thickness strain heterogeneity after roll bonding of dissimilar materials. FE modeling was used at two length scales to study the deformation and texture heterogeneities inside a 9-layer multilaminate made of aluminum and steel, produced by roll-bonding. Microstructure and crystallographic texture were probed using EBSD. Numerical predictions indicated that plane strain compression was accompanied by significant shear parallel to the rolling plane and inclined shear banding in aluminum. Predictions of the Texture development were more accurate in the bcc phase than the fcc phase.

Keywords
Roll-Bonding, Anisotropic Plasticity, Finite Element

Published online 4/24/2024, 8 pages
Copyright © 2024 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA

Citation: HANON Guillaume, MALET Loïc, DELANNAY Laurent, Heterogeneity of strain and texture inside roll-bonded multilaminates, Materials Research Proceedings, Vol. 41, pp 1724-1731, 2024

DOI: https://doi.org/10.21741/9781644903131-191

The article was published as article 191 of the book Material Forming

Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.

References
[1] Hosseini, M., Pardis, N., Manesh, H. D., Abbasi, M., & Kim, D. I. (2017). Structural characteristics of Cu/Ti bimetal composite produced by accumulative roll-bonding (ARB). Materials & Design, 113, 128-136. https://doi.org/10.1016/j.matdes.2016.09.094
[2] McCabe, R. J., Nizolek, T. J., Li, N., Zhang, Y., Coughlin, D. R., Miller, C., & Carpenter, J. S. (2021). Evolution of microstructures and properties leading to layer instabilities during accumulative roll bonding of FeCu, FeAg, and FeAl. Materials & Design, 212, 110204. https://doi.org/10.1016/j.matdes.2021.110204
[3] Govindaraj, N. V., Frydendahl, J. G., & Holmedal, B. (2013). Layer continuity in accumulative roll bonding of dissimilar material combinations. Materials & Design (1980-2015), 52, 905-915. https://doi.org/10.1016/j.matdes.2013.06.031
[4] Mishin, O. V., Bay, B., & Jensen, D. J. (2000). Through-thickness texture gradients in cold-rolled aluminum. Metallurgical and Materials Transactions A, 31, 1653-1662. https://doi.org/10.1007/s11661-000-0175-2
[5] Engler, O., Tomé, C. N., & Huh, M. Y. (2000). A study of through-thickness texture gradients in rolled sheets. Metallurgical and materials transactions A, 31(9), 2299-2315. https://doi.org/10.1007/s11661-000-0146-7
[6] Schoenfeld, S.E., Asaro, R.J.: Through thickness texture gradients in rolled polycrystalline alloys. Int. J. Mech. Sci. 38(6), 661–683 (1996). https://doi.org/10.1016/S0020-7403(96)80008-7
[7] Lin, F., Marteleur, M., Jacques, P. J., & Delannay, L. (2018). Transmission of {332}< 113> twins across grain boundaries in a metastable β-titanium alloy. International Journal of Plasticity, 105, 195-210. https://doi.org/10.1016/j.ijplas.2018.02.012
[8] Li, Z., Li, L. Y., Zhu, Y. B., Lin, K., Ren, Z. T., Yang, Y., … & Langdon, T. G. (2022). Evidence for a stable single component sharp texture in high purity aluminum during tube high-pressure shearing at room temperature. Scientific Reports, 12(1), 17901. https://doi.org/10.1038/s41598-022-21717-z
[9] Hanon, G., Malet, L., Delannay, L. (2023). Texture and Microstructure After Roll-Bonding of an Fe-Al Multilaminate. In: Mocellin, K., Bouchard, PO., Bigot, R., Balan, T. (eds) Proceedings of the 14th International Conference on the Technology of Plasticity – Current Trends in the Technology of Plasticity. ICTP 2023. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-031-40920-2_67
[10] Sidor, J., Petrov, R., & Kestens, L. (2014). Texture control in aluminum sheets by conventional and asymmetric rolling. In Comprehensive materials processing, vol. 3: advanced forming technologies (pp. 447-498). Elsevier. https://doi.org/10.1016/B978-0-08-096532-1.00324-1
[12] Tieu, A. K., & Liu, Y. J. (2004). Friction variation in the cold-rolling process. Tribology International, 37(2), 177-183. https://doi.org/10.1016/S0301-679X(03)00048-3