–
Tension-compression asymmetry of ferritic stainless steel sheet
Sekiya Koki, Higashii Hyuga, Taoka Akira, Kuwabara Toshihiko
download PDFAbstract. The strength differential effect (SDE) (i.e., the tension-compression asymmetry of stress-strain curves), for a ferritic stainless steel sheet was measured using an in-plane compression test. It was found that the in-plane compressive flow stress was 4-7% higher than the uniaxial tensile flow stress in both the rolling and transverse directions. In addition, bending moment-curvature curves were obtained from a pure bending test. These curves were found to be in good agreement with those calculated with SDE taken into account. Thus, the validity of the measured SDE was confirmed by the bending experiment.
Keywords
In-Plane Compression, Strength Differential Effect, Bending Moment
Published online 4/24/2024, 9 pages
Copyright © 2024 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: Sekiya Koki, Higashii Hyuga, Taoka Akira, Kuwabara Toshihiko, Tension-compression asymmetry of ferritic stainless steel sheet, Materials Research Proceedings, Vol. 41, pp 1106-1114, 2024
DOI: https://doi.org/10.21741/9781644903131-122
The article was published as article 122 of the book Material Forming
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] J. Hamada, A. Hayashi, N. Kanno, T. Komori, H. Ito, N. Fukuda, Y. Inoue, Development of Heat-resistant Ferritic Stainless Steels “NSSC429NF” and “NSSC448EM” Utilized Dynamic Precipitation Hardening for Automotive Exhaust Systems, Materia Japan 56 (2017) 33-35. (in Japanese) https://doi.org/10.2320/materia.56.33
[2] W.A. Spitzig, R.J. Sober, O. Richmond, Pressure dependence of yielding and associated volume expansion in tempered martensite, Acta Metall. 23 (1975), 885-893.
https://doi.org/10.1016/0001-6160(75)90205-9
[3] W.A. Spitzig, R.J. Sober, O. Richmond, O., The effect of hydrostatic pressure on the deformation behavior of maraging and HY-80 steels and its implication for plasticity, Met. Trans. 7A (1976) 1703-1710. https://doi.org/10.1007/BF02817888
[4] O. Richmond, W.A. Spitzig, Pressure dependence and dilatancy of plastic flow, IUTAM Conference, Theoretical and Applied Mechanics, Proc. 15th International Congress of Theoretical and Applied Mechanics. North-Holland Publishers, Amsterdam, 1980, pp. 377–386.
[5] W.A. Spitzig, O. Richmond, The effect of pressure on the flow stress of metals, Acta Metall. 32 (1984) 457-463. https://doi.org/10.1016/0001-6160(84)90119-6
[6] T. Kuwabara, Y. Morita, Y. Miyashita, S. Takahashi, Elastic-Plastic Behavior of Sheet Metal Subjected to In-Plane Reverse Loading, in S. Tanimura, A.S. Khan (Eds.), Proc. Plasticity ‘95, The fifth international symposium on plasticity and its current applications, Gordon and Breach Publishers, 1995, pp.841-844,.
[7] T. Maeda, N. Noma, T. Kuwabara, F. Barlat, Y.P. Korkolis, Measurement of the strength differential effect of DP980 steel sheet and experimental validation using pure bending test, J. Mater. Process. Technol. 256 (2018) 247-253. https://doi.org/10.1016/j.jmatprotec.2018.02.009
[8] N. Noma, K. Hashimoto, T. Maeda, T. Kuwabara, Enhancement of Accuracy of Springback Simulation Using the Material Model Considering the Strength Differential Effect, J. JSTP 61 (2020) 20-25. (in Japanese). https://doi.org/10.9773/sosei.61.20
[9] T. Kuwabara, R. Tachibana, Y. Takada, T. Koizumi, S. Coppieters, F. Barlat, Effect of hydrostatic stress on the strength differential effect in low-carbon steel sheet, Int. J. Material Forming 15 (2022) 13. https://doi.org/10.1007/s12289-022-01650-2
[10] T. Kuwabara, R. Saito, T. Hirano, N. Oohashi, Tension–Compression Asymmetry of SUS304 Stainless Sheet for Electronic Parts and Its Effects on Bending and Springback Behavior, Tetsu-to-Hagané 95 (2009) 732-739. (in Japanese). https://doi.org/10.2355/tetsutohagane.95.732
[11] S.Y. Yoon, F. Barlat, S.Y. Lee, J.H. Kim, M.S. Wi, D.J. Kim, Finite element implementation of hydrostatic pressure-sensitive plasticity and its application to distortional hardening model and sheet metal forming simulations, J. Mater. Processing Technol. 302 (2022) 117494. https://doi.org/10.1016/j.jmatprotec.2022.117494
[12] F. Barlat, S.Y. Yoon, S.Y. Lee, M.S. Wi, J.H. Kim, Distortional plasticity framework with application to advanced high strength steel, Int. J. Solids Struct. 202 (2020) 947-962.
https://doi.org/10.1016/j.ijsolstr.2020.05.014
[13] N. Noma, T. Kuwabara, Specimen Geometry Optimization for In-plane Reverse Loading Test of Sheet Metal and Experimental Validation, J. JSTP 53 (2012) 574-579. (in Japanese). https://doi.org/10.9773/sosei.53.574
[14] K. Akiyama, R. Tachibana, T. Sakurai, T. Kuwabara: submitted to J. Materials Processing Technology (2024).