Development of a Hybrid Method for Identifying the Causes of Product Incompatibility in Metallurgical Manufacturing
DWORNICKA Renata, SIWIEC Dominika, PACANA Andrzej
download PDFAbstract. For the analysis of the quality of metallurgical products, it is important to use techniques that identify the internal and external unconformity of the product without destroying it. These techniques are non-destructive testing (NDT). Although these techniques identify the unconformity of the product, they do not indicate the source of their creation. The purpose of the study was to develop a hybrid method to make decisions about the causes of product incompatibility. This hybrid method was created as a combination of NDT and quality management techniques, i.e.: 5W2H method, Ishikawa diagram, 5Why method. The subject of the study was an unconformity detected in the tube made of the magnesium alloy AMS 4439. Research was carried out using the FPI method. In the analyzed case, its application allowed the detection of a linear indication in the product. To identify the root of the linear indication, the 5W2H method, the Ishikawa diagram, and the 5Why method were used sequentially. The main causes were bad casting and pollution. The root cause was defective supplier material. Integration of the FPI method, the 5W2H method, the Ishikawa diagram, and the 5Why method in the performance of a comprehensive qualitative analyze of products, after which it is possible to identify the unconformity and the root of its occurrence. The integration of FPI and quality management techniques can be practiced to analyze the quality of products (including metallurgical products) in manufacturing and service enterprises.
Keywords
Mechanical Engineering, Quality Management, Making Decision, Non-Destructive Testing
Published online 9/1/2023, 8 pages
Copyright © 2023 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: DWORNICKA Renata, SIWIEC Dominika, PACANA Andrzej, Development of a Hybrid Method for Identifying the Causes of Product Incompatibility in Metallurgical Manufacturing, Materials Research Proceedings, Vol. 34, pp 199-206, 2023
DOI: https://doi.org/10.21741/9781644902691-24
The article was published as article 24 of the book Quality Production Improvement and System Safety
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 license. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] J. Zheng et al. Design of an advanced automatic inspection system for aircraft parts based on fluorescent penetrant inspection analysis, Insight: Non-Destr. Test. Cond. Monit. 57 (2015) 18-34. https://doi.org/10.1784/insi.2014.57.1.18
[2] L.J.H. Brasche et al. Characterization of developer application methods used in fluorescent penetrant inspection, AIP Conf. Proc. 820 (2006) 598-605. https://doi.org/10.1063/1.2184582
[3] H. Fischer et al. Detection of microscopic cracks in dental ceramic materials by fluorescent penetrant method, J. Biomed. Mater. Res. 61(1) (2002) 153-158. https://doi.org/10.1002/jbm.10148
[4] N. J. Shipway et al. Performance Based Modifications of Random Forest to Perform Automated Defect Detection for Fluorescent Penetrant Inspection, J. Nondestructive Evaluation 38 (2019) art. 37. https://doi.org/10.1007/s10921-019-0574-9
[5] R. Wong, K. Cunningham. Mechanical processing of aluminum alloy components and its effect on fluorescent penetrant indications. Mater. Eval. 64 (2006) 1180-1186.
[6] N. J. Shipway et al. Automated defect detection for Fluorescent Penetrant Inspection using Random Forest, NDT & E International 101 (2019) 113-123. https://doi.org/10.1016/j.ndteint.2018.10.008
[7] K. Daneshvar, B. Dogan. Application of quantum dots as a fluorescent-penetrant for weld crack detection, Mater. at High Temp. 27 (2010) 179-182. https://doi.org/10.3184/096034010X12813744660988
[8] A.S. Bakunov et al. Increasing the reliability of magnetic-particle testing by means of a YMJIK-10 automated unit for magnetic fluorescent-penetrant inspection of pipe end faces, Russian J. Nondestruct. Test. 40 (2004) 311-316. https://doi.org/10.1023/B:RUNT.0000045935.55674.d3
[9] L. Brasche et al. Engineering studies for fluorescent penetrant inspection with a focus on developer application methods, Insight: Non-Destr. Test. Cond. Monit. 51 (2009) 88-91. https://doi.org/10.1784/insi.2009.51.2.88
[10] P. Ewert P., C.T. Kowalski. Detection of the damage of the submerged pump aggregates with induction motors. Prace Naukowe Instytutu Maszyn, Napędów i Pomiarów Elektrycznych Politechniki Wrocławskiej. Studia i Materiały 69 (2013) 181-193.
[11] S. Borkowski, R. Ulewicz, J. Selejdak, M. Konstanciak, D. Klimecka-Tatar. The use of 3×3 matrix to evaluation of ribbed wire manufacturing technology, METAL 2012 – 21st Int. Conf. Metallurgy and Materials (2012), Ostrava, Tanger 1722-1728.
[12] R. Ulewicz, F. Nový. Quality management systems in special processes, Transp. Res. Procedia 40 (2019) 113-118. https://doi.org/10.1016/j.trpro.2019.07.019
[13] T. Lipiński, R. Ulewicz. The effect of the impurities spaces on the quality of structural steel working at variable loads, Open Eng. 11 (2021) 233-238. https://doi.org/10.1515/eng-2021-0024
[14] R. Ulewicz, J. Selejdak, S. Borkowski, M. Jagusiak-Kocik. Process management in the cast iron foundry, METAL 2013 – 22nd Int. Conf. Metallurgy and Materials (2013), Ostrava, Tanger 1926-1931.
[15] R. Ulewicz, D. Jelonek, M. Mazur. Implementation of logic flow in planning and production control, Management and Production Engineering Review 7 (2016) 89-94. https://doi.org/10.1515/mper-2016-0010
[16] J. Fabiś-Domagała, G. Filo, H. Momeni, M. Domagała. Instruments of identification of hydraulic components potential failures, MATEC Web of Conf. 183 (2018) art.03008. https://doi.org/10.1051/matecconf/201818303008
[17] K. Knop et al. Evaluating and Improving the Effectiveness of Visual Inspection of Products from the Automotive Industry, Lecture Notes in Mechanical Engineering (2019) 231-243. https://doi.org/10.1007/978-3-030-17269-5_17
[18] P. Lempa, G. Filo. Analysis of Neural Network Training Algorithms for Implementation of the Prescriptive Maintenance Strategy, Mater. Res. Proc. 24 (2022) 281-287. https://doi.org/10.21741/9781644902059-41
[19] P. Jonšta et al. The effect of rare earth metals alloying on the internal quality of industrially produced heavy steel forgings, Materials 14 (2021) art.5160. https://doi.org/10.3390/ma14185160
[20] N. Radek et al. Technology and application of anti-graffiti coating systems for rolling stock, METAL 2019 28th Int. Conf. Metall. Mater. (2019) 1127-1132. ISBN 978-8087294925
[21] N. Radek et al. Influence of laser texturing on tribological properties of DLC coatings, Prod. Eng. Arch. 27 (2021) 119-123. https://doi.org/10.30657/pea.2021.27.15
[22] N. Radek et al. Formation of coatings with technologies using concentrated energy stream, Prod. Eng. Arch. 28 (2022) 117-122. https://doi.org/10.30657/pea.2022.28.13
[23] N. Radek, J. Pietraszek, A. Gadek-Moszczak, Ł.J. Orman, A. Szczotok. The morphology and mechanical properties of ESD coatings before and after laser beam machining, Materials 13 (2020) art. 2331. https://doi.org/10.3390/ma13102331
[24] N. Radek et al. The effect of laser treatment on operational properties of ESD coatings, METAL 2021 30th Ann. Int. Conf. Metall. Mater. (2021) 876-882. https://doi.org/10.37904/metal.2021.4212
[25] N. Radek et al. The impact of laser processing on the performance properties of electro-spark coatings, 14th World Congress in Computational Mechanics and ECCOMAS Congress 1000 (2021) 1-10. https://doi.org/10.23967/wccm-eccomas.2020.336
[26] N. Radek et al. The influence of plasma cutting parameters on the geometric structure of cut surfaces, Mater. Res. Proc. 17 (2020) 132-137. https://doi.org/10.21741/9781644901038-20
[27] A. Goroshko et al. Construction and practical application of hybrid statistically-determined models of multistage mechanical systems, Mechanika 20 (2014) 489-493. https://doi.org/10.5755/j01.mech.20.5.8221
[28] R. Ulewicz, M. Mazur. Economic aspects of robotization of production processes by example of a car semi-trailers manufacturer, Manufacturing Technology 19 (2019) 1054-1059. https://doi.org/10.21062/ujep/408.2019/a/1213-2489/MT/19/6/1054
[29] I. Drach et al. Design Principles of Horizontal Drum Machines with Low Vibration, Adv. Sci. Technol. Res. J. 15 (2021) 258-268. https://doi.org/10.12913/22998624/136441
[30] N. Radek et al. Operational tests of coating systems in military technology applications, Eksploat. i Niezawodn. 25 (2023) art.12. https://doi.org/10.17531/ein.2023.1.12
[31] W. Przybył et al. Microwave absorption properties of carbonyl iron-based paint coatings for military applications, Def. Technol. 22 (2023) 1-9. https://doi.org/10.1016/j.dt.2022.06.013
[32] S. Borkowski, R. Ulewicz, J. Selejdak, M. Konstanciak, D. Klimecka-Tatar. The use of 3×3 matrix to evaluation of ribbed wire manufacturing technology, METAL 2012 – 21st Int. Conf. Metallurgy and Materials (2012), Ostrava, Tanger 1722-1728.
[33] L. Cedro Model parameter on-line identification with nonlinear parametrization – manipulator model, Technical Transactions 119 (2022) art. e2022007. https://doi.org/10.37705/TechTrans/e2022007
[34] J. Pietraszek, A. Szczotok, N. Radek. The fixed-effects analysis of the relation between SDAS and carbides for the airfoil blade traces. Archives of Metallurgy and Materials 62 (2017) 235-239. https://doi.org/10.1515/amm-2017-0035
[35] J. Pietraszek, N. Radek, A.V. Goroshko. Challenges for the DOE methodology related to the introduction of Industry 4.0. Production Engineering Archives 26 (2020) 190-194. https://doi.org/10.30657/pea.2020.26.33
[36] B. Jasiewicz et al. Inter-observer and intra-observer reliability in the radiographic measurements of paediatric forefoot alignment, Foot Ankle Surg. 27 (2021) 371-376. https://doi.org/10.1016/j.fas.2020.04.015
[37] J. Pietraszek. The modified sequential-binary approach for fuzzy operations on correlated assessments, LNAI 7894 (2013) 353-364. https://doi.org/10.1007/978-3-642-38658-9_32
[38] J. Pietraszek et al. Non-parametric assessment of the uncertainty in the analysis of the airfoil blade traces, METAL 2017 26th Int. Conf. Metall. Mater. (2017) 1412-1418. ISBN 978-8087294796
[39] J. Pietraszek et al. The non-parametric approach to the quantification of the uncertainty in the design of experiments modelling, UNCECOMP 2017 Proc. 2nd Int. Conf. Uncert. Quant. Comput. Sci. Eng. (2017) 598-604. https://doi.org/10.7712/120217.5395.17225
[40] J. Pietraszek, E. Skrzypczak-Pietraszek. The uncertainty and robustness of the principal component analysis as a tool for the dimensionality reduction. Solid State Phenom. 235 (2015) 1-8. https://doi.org/10.4028/www.scientific.net/SSP.235.1
[41] A. Pacana, D. Siwiec. Universal Model to Support the Quality Improvement of Industrial Products, Materials 14 (2021) art. 7872. https://doi.org/10.3390/ma14247872
[42] A. Pacana et al. Analysis of the incompatibility of the product with fluorescent method, Metalurgija 58(3-4) (2019) 337-340.
[43] A. Pacana et al. Comprehensive improvement of the surface quality of the diesel engine piston, Metalurgija, 58(3-4) (2019), 329-332.
[44] D. Siwiec, A. Pacana. A New Model Supporting Stability Quality of Materials and Industrial Products, Materials 15 (2022) art. 4440. https://doi.org/10.3390/ma15134440
[45] M. Korzyński, A. Pacana. Centreless burnishing and influence of its parameters on machining effects, J. Mater. Process. Technol. 210 (2010) 1217-1223. https://doi.org/10.1016/j.jmatprotec.2010.03.008
[46] A. Pacana et al. Study on improving the quality of stretch film by Shainin method, Przemysl Chemiczny 93 (2014), 243-245. https://doi.org/10.12916/przemchem.2014.243
[47] D. Siwiec, A. Pacana. A Pro-Environmental Method of Sample Size Determination to Predict the Quality Level of Products Considering Current Customers’ Expectations, Sustainability 13 (2021) art.5542. https://doi.org/10.3390/su13105542
[48] A. Gazda et al., Study on improving the quality of stretch film by Taguchi method, Przemysl Chemiczny, 92 6(2013), 980-982.
[49] R. Wolniak. Application methods for analysis car accident in industry on the example of power, Support Systems in Production Engineering 6 (2017) 34-40.
