Improving the Non-Destructive Test by initiating the Quality Management Techniques on an Example of the Turbine Nozzle Outlet
SIWIEC Dominika, DWORNICKA Renata and PACANA Andrzej
download PDFAbstract. The NDT methods are an effective way to make a quality analysis of the product, mainly in the case of the aviation industry. However, although these studies effectively identify unconformities, they do not indicate the source of their occurrence. The aim was to analyze the quality of the product (turbine nozzle outlet) using the fluorescent method and identify the root of the unconformity by using the quality management technique sequence. The Ishikawa diagram and the 5Why method were the techniques used in the study and the turbine nozzle outlet made from 410 steel was its subject. The product using the fluorescent method was analyzed, after which the unconformity was identified (porosity cluster). By using the Ishikawa diagram, the potential causes were identified, from which two main causes were selected (molding sand and errors during production). The 5Why method was used, by means of which the root cause was identified – it was a faulty material form a supplier. On the example of the fluorescent method, it was shown that using the non-destructive test (NDT) in a sequential way with quality management techniques (Ishikawa diagram and 5Why method) allows for making a complex quality analysis of the product and identifying the root of eventual unconformity. The proposed technique sequence (fluorescent method, Ishikawa diagram and 5Why method) can be applied to analyze other products and other unconformities in production and service enterprises.
Keywords
Mechanical Engineering, Turbine Nozzle Outlet, Quality Management, Non-Destructive Test, Fluorescent Method
Published online , 7 pages
Copyright © 2020 by the author(s)
Published under license by Materials Research Forum LLC., Millersville PA, USA
Citation: SIWIEC Dominika, DWORNICKA Renata and PACANA Andrzej, Improving the Non-Destructive Test by initiating the Quality Management Techniques on an Example of the Turbine Nozzle Outlet, Materials Research Proceedings, Vol. 17, pp 16-22, 2020
DOI: https://doi.org/10.21741/9781644901038-3
The article was published as article 3 of the book Terotechnology XI
Content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
References
[1] R. Ulewicz, Quality control system in production of the castings from spheroid cast iron, Metalurgija 42(1) (2003) 61-63.
[2] A. Pacana, L. Bednárová, I. Liberko etal., Effect of selected production factors of the stretch film on its extensibility, Przemysl Chemiczny 93(7) (2014) 1139-1140
[3] J. Zheng, W. F. Xie, M. Viens et al., Design of an advanced automatic inspection system for aircraft parts based on fluorescent penetrant inspection analysis, INSIGHT 57(1) (2015) 18 34. https://doi.org/10.1784/insi.2014.57.1.18
[4] L. J. H. Brasche, R. Lopez, D. Eisenmann, Characterization of developer application methods used in fluorescent penetrant inspection, Review of Progress in Quantitative Nondestructive Evaluation. Vols. 25a and 25b, AIP Conference Proceedings 820 (2006) 598 605. https://doi.org/10.1063/1.2184582
[5] H. Fischer, F. Karaca, R. Marx, Detection of microscopic cracks in dental ceramic materials by fluorescent penetrant method, Journal of Biomedical Materials Research 61(1) (2002) 153-158. https://doi.org/10.1002/jbm.10148
[6] N. J. Shipway, P. Huthwaite, M. J. S. Lowe et al., Performance Based Modifications of Random Forest to Perform Automated Defect Detection for Fluorescent Penetrant Inspection, Journal of Nondestructive Evaluation 38(2) (2019) 1-11. https://doi.org/10.1007/s10921-019-0574-9
[7] J. Zheng, W. F. Xie, M. Viens, M. et al., Design of an advanced automatic inspection system for aircraft parts based on fluorescent penetrant inspection analysis, INSIGHT 57(1) (2015) 18-34. https://doi.org/10.1784/insi.2014.57.1.18
[8] K. Daneshvar, B. Dogan, Application of quantum dots as a fluorescent-penetrant for weld crack detection, Materials at High Temperatures 27(3) (2010) 179-182. https://doi.org/10.3184/096034010X12813744660988
[9] Y. Guo, F. R. Ruhge, Comparison of detection capability for acoustic thermography, visual inspection and fluorescent penetrant inspection on gas turbine components, Review of Progress in Quantitative Nondestructive Evaluation, (28A and 28B), AIP Conference Proceedings, 1096 (2009) 1848. https://doi.org/10.1063/1.3114183
[10] G. Filo, E. Lisowski, M. Domagala, J. Fabis-Domagala, H. Momeni, Modelling of pressure pulse generator with the use of a flow control valve and a fuzzy logic controller. MSM 2018 14th Int. Conf. Mechatronic Systems and Materials, AIP Conference Proceedings, vol. 2029, art. 020015-1. https://doi.org/10.1063/1.5066477
[11] P. Krawiec, M. Grzelka, J. Kroczak, G. Domek, A. Kolodziej, A proposal of measurement methodology and assessment of manufacturing methods of nontypical cog belt pulleys. Measurement 132 (2019) 182-190. https://doi.org/10.1016/j.measurement.2018.09.039
[12] M. Domagala, H. Momein, J. Domagala-Fabis, G. Filo, M. Krawczyk, J. Rajda, Simulation of particle erosion in a hydraulic valve. Materials Research Proceedings 5 (2018) 17-24.
[13] L. J. Orman, Boiling heat transfer on meshed surfaces of different aperture. AIP Conf. Proc. 1608 (2014) 169-172. https://doi.org/10.1063/1.4892728
[14] D. Przestacki, M. Kuklinski, A. Bartkowska, Influence of laser heat treatment on microstructure and properties of surface layer of Waspaloy aimed for laser-assisted machining. Int. J. Adv. Manuf. Technol. 93 (2017) 3111-3123. https://doi.org/10.1007/s00170-017-0775-2
[15] S. Wojciechowski, D. Przestacki, T. Chwalczuk, The evaluation of surface integrity during machining of Inconel 718 with various laser assistance strategies. MATEC Web of Conf. 136 (2017) art. 01006. https://doi.org/10.1051/matecconf/201713601006
[16] W. Zorawski, R. Chatys, N. Radek, J. Borowiecka-Jamrozek, Plasma-sprayed composite coatings with reduced friction coefficient. Surf. Coat. Technol. 202 (2008) 4578-4582. https://doi.org/10.1016/j.surfcoat.2008.04.026
[17] N. Radek, K. Bartkowiak, Laser treatment of electro-spark coatings deposited in the carbon steel substrate with using nanostructured WC-Cu electrodes. Physics Procedia. 39 (2012) 295-301. https://doi.org/10.1016/j.phpro.2012.10.041
[18] I. Pliszka, N. Radek, A. Gadek-Moszczak, P. Fabian, O. Paraska, Surface improvement by WC-Cu electro-spark coatings with laser modification. Materials Research Proceedings 5 (2018) 237-242. https://doi.org/10.5604/01.3001.0010.5906
[19] E. Skrzypczak-Pietraszek, A. Hensel, Polysaccharides from Melittis melissophyllum L. herb and callus. Pharmazie 55 (2000) 768-771.
[20] E. Skrzypczak-Pietraszek, A. Urbanska, P. Zmudzki, J. Pietraszek, Elicitation with methyl jasmonate combined with cultivation in the Plantform™ temporary immersion bioreactor highly increases the accumulation of selected centellosides and phenolics in Centella asiatica (L.) Urban shoot culture. Engineering in Life Sciences. 19 (2019) 931-943. https://doi.org/10.1002/elsc.201900051
[21] A. Szczotok, D. Karpisz, Application of two non-commercial programmes to image processing and extraction of selected features occurring in material microstructure. METAL 2019: 28th Int. Conf. on Metallurgy and Materials, Ostrava, TANGER, 1721-1725. https://doi.org/10.37904/metal.2019.971
[22] L. Wojnar, A. Gadek-Moszczak, J. Pietraszek, On the role of histomorphometric (stereological) microstructure parameters in the prediction of vertebrae compression strength. Image Analysis and Stereology 38 (2019) 63-73. https://doi.org/10.5566/ias.2028
[23] J. Pietraszek, E. Skrzypczak-Pietraszek, The optimization of the technological process with the fuzzy regression. Adv. Mater. Res-Switz. 874 (2014) 151-155. https://doi.org/10.4028/www.scientific.net/AMR.874.151
[24] J. Pietraszek, A. Gadek-Moszczak, T. Torunski, Modeling of Errors Counting System for PCB Soldered in the Wave Soldering Technology. Advanced Materials Research 874 (2014) 139-143. https://doi.org/10.4028/www.scientific.net/AMR.874.139
[25] D. C. Moreira., H. C. Furtado, J. S. Buarque, et al., Failure analysis of AISI 410 stainless-steel piston rod in spillway floodgate, Engineering Failure Analysis 97 (2019) 506-517. https://doi.org/10.1016/j.engfailanal.2019.01.035
[26] F. Hejripour,D. K. Aidun, Consumable selection for arc welding between Stainless Steel 410 and Inconel 718, Journal of Materials Processing Technology 245 (2017) 287-299. https://doi.org/10.1016/j.jmatprotec.2017.02.013
[27] M. Moradi, H. Arabi., S. J. Nasab et al., A comparative study of laser surface hardening of AISI 410 and 420 martensitic stainless steels by using diode laser, Optics and Laser Technology 111 (2019) 347-357. https://doi.org/10.1016/j.optlastec.2018.10.013
[28] T. S. Oliveira, E. S Silva, S. F Rodrigues et al., Softening Mechanisms of the AISI 410 Martensitic Stainless Steel Under Hot Torsion Simulation, Materials Research-Ibero-American Journal of Materials 20(2) (2017) 395-406. https://doi.org/10.1590/1980-5373-mr-2016-0795
[29] A. Pacana, D. Siwiec, L. Bednárová, Analysis of the incompatibility of the product with fluorescent method, Metalurgija 58 3-4 (2019) 337-340.
[30] D. Siwiec, L. Bednarova, A. Pacana., M. Zawada, M. Rusko, Decision support in the selection of fluorescent penetrants for industrial non-destructive testing, Przemysl Chemiczny 98(10) (2019) 1594-1596.
[31] A. Pacana, A. Radon-Cholewa, J. Pacana J. et al., The study of stickiness of packaging film by Shainin method, Przemysl Chemiczny 94(8) (2015) 1334-1336.
[32] https://www.e-spawalnik.pl/?wybor-metody-badannieniszczacych,168 (access: 11.10.2019)
[33] D. Malindzak, et al., An effective model for the quality of logistics and improvement of environmental protection in a cement plant, Przemysl Chemiczny 96(9) (2019) 1958-1962.
[34] R. Wolniak, Application methods for analysis car accident in industry on the example of power, Support Systems in Production Engineering 6(4) (2017) 34-40.
[35] Radek, N., Kurp, P., Pietraszek, J., Laser forming of steel tubes. Technical Transactions 116 (2019) 223-229. https://doi.org/10.4467/2353737XCT.19.015.10055
